750004
12
Zoom out
Zoom in
Previous page
1/130
Next page
Introduction
Cut Function
Touch the cut function button and your machine cuts
the upper and bobbin threads and raises the presser foot
and needle.
To cut threads at the end of a stitch or stitch sequence,
touch the cut function button while sewing. The
indicator light will intensify, alerting you that a cut is
requested. When the stitch or stitch sequence is
completed, your machine cuts the upper and bobbin
threads and raises the presser foot and needle.
Note: If automatic presser foot lift has been deselected in
temporary session settings the presser foot will not be raised
when using the cut function.
Some optional accessories are attached in the two
small circular holes in the needle plate just above the
bobbin cover. Do not use the cut function when an
accessory is attached in these holes as that may
interfere with the automatic thread cutter located
under the needle plate.
Immediate Tie-Off
Press immediate tie-off while sewing and your machine
sews a few tie-off stitches and stops automatically. By
touching the tie-off button once more while the action
indicator is lit, the function can be turned off.
Stitch Re-Start
When you stop sewing in the middle of a stitch, touch
stitch re-start to begin sewing at the beginning of the
stitch. The stitch or stitch sequence will remember any
special settings you made.
Needle Stop Up/Down
Touch needle stop up/down to set the position of the
needle when you stop sewing. The needle will move up
or down when you touch the button. The indicator light
intensifies when needle stop down is set.
Tip: You can also tap the foot control to raise or lower the
needle once you stop sewing. Tapping the foot control does not
change the set stop position.
Start/Stop
Touch the start/stop button to start and stop the
machine sewing without using the foot control. Touch
start/stop to begin and touch again to stop.
Reverse
When reverse is active, the reverse indicator intensifies.
For permanent reverse, touch the reverse button once
before starting to sew. The reverse indicator will
intensify and the machine sews in reverse until you
touch the button again to cancel. If you press the reverse
button while sewing, the machine will sew in reverse for
as long as you keep the button pressed.
Reverse is also used when sewing manual buttonholes,
darning stitches and tapering stitches to step between
the parts of the stitch.
12
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pfaff Performance Icon at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pfaff Performance Icon in the language / languages: English as an attachment in your email.

The manual is 11,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pfaff Performance Icon

Pfaff Performance Icon User Manual - German - 140 pages

Pfaff Performance Icon User Manual - Dutch - 138 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info