478200
56
Zoom out
Zoom in
Previous page
1/58
Next page
Maintenance
and
troubleshooting
Sewing
problems
and
their
solutions
Problem/Cause
1.
The
machine
skips
stitches
The
needle
is
not
properly
inserted.
Wrong
needle
is
in
use.
Needle
is
bent
or
blunt.
The
machine
is
not
properly
threaded.
Needle
is
too small
for
thread.
2.
Needle
thread
breaks
See
reasons
above.
Thread
tension
is
too
tight.
Thread
is
poor
or
has
slubs
in
it,
or
has
become
dry
after
overlong
storage.
Thread
is
too
thick.
3.
Needle
breaks
off
Needle
is
not
pushed
fully
in.
Needle
is
bent.
Needle
is
too
thick
or
too
thin.
Needle
is
bent,
and
has
hit
the
needle
plate
because
you
are
pulling
or
pushing
the
fabric.
The
bobbin
case
is
not
properly
inserted,
4.
The
seam
is
sewn
unevenly
The tension
needs
adjusting,
Thread
is
too
thick,
slubbed
or
hard.
The
bobbin
thread
is
unevenly
wound.
Thread
loops
at
top
or
underside
of
fabric.
6.
The
machine
is
running
with
difficulty
There
are
thread
remnants
in
the
hook
ways.
Remedy
Push
needle
fully
upwards.
Flat
side
facing
the
back.
Use
needle
system
130/705
H.
Insert
a
new
needle.
Check
how
the
machine
is
threaded.
Use
a
larger
needle.
See
above.
Adjust
thread
tension.
Only
use
good
quality
threads.
Use
needle
with
large
eye
(system
130
N).
Insert
new
needle
and
push
fully
in.
Insert
new
needle.
See
needle
table
(Page
59,
60).
Only
guide
the
fabric
lightly.
When
you
insert
the
bobbin
case,
push
it
fully
into
the
stop.
Pull
lightly
on
the
end
of
the
thread
to
make
sure
bobbin
case
is
secure.
Check
needle
and
bobbin
thread
tensions.
Only
use
good
quality
threads.
Do
not
wind
thread
by
hand.
Make
sure
thread
is
pulled
solidly
into
bobbin
tension
spring.
Re4hread
machine.
Check
the
needle
and
bobbin
thread
tensions.
Remove
the
threads
and
apply
a
drop
of
oil
to
the
hook.
Important
notes:
Before
changing
presser
feet
and
needle
the
master
switch
must
be
switched
off.
Do
not
attempt
to
sew
without
fabric
under
the
presser
foot.
When
leaving
the
machine,
even
for
only
a
short
time,
switch
off
the
master
switch.
This
is
important
if
there
are
any
children
nearby
5.
The
machine
does
not
feed
or
feeds
irregularly
Sewing
lint
has
collected
between
Remove
needle
plate,
the
feed
dog
teeth
rows,
remove
lint
with
brush.
52
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pfaff Hobby 1016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pfaff Hobby 1016 in the language / languages: English as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info