478189
7
Zoom out
Zoom in
Previous page
1/52
Next page
Introduction
Presser feet
Standard presser foot 0A with IDT (attached on the machine upon delivery)
This foot is used mainly for straight stitching and zigzag stitching with a stitch length
longer than 1.0 mm.
Fancy stitch foot 1A with IDT
This foot is used for decorative stitches. The groove on the underside of the foot is
designed to Á ow smoothly over the stitches.
Fancy stitch foot 2A
When sewing decorative stitches or short zigzag stitches and other utility stitches with
less than 1.0mm stitch length, use this foot. The groove on the underside of the foot is
designed to Á ow smoothly over the stitches.
Blindhem foot 3 with IDT
This foot is used for blindhem stitches. The toe on the foot guides the fabric. The red
guide on the foot is designed to ride along the fold of the hem edge.
Zipper foot 4 with IDT
This foot can be snapped on either the right or the left of the needle, making it easy to
sew close to both sides of the zipper teeth. Move the needle position to the right or left to
sew closer to zipper teeth.
Sensormatic buttonhole foot 5A
When connected to the machine, the buttonhole is sewn in a suitable length to the button
size that has been entered into the machine.
Manual buttonhole foot 5M
This foot is used for sewing manual buttonholes. Use the markings on the foot to position
the garment edge. The À nger on the back of the foot holds cording for corded buttonhole.
Sensormatic free-motion foot 6A (4.0)
This foot is used for sensormatic free-motion sewing. This foot can also be used for
darning.
Rolled hem foot 7 with IDT, 3 mm
This foot is used to sew narrow hems in light to medium weight fabric.
1/4” quilting foot with IDT (4.0)
This foot is perfect for piecing and patchwork, especially when used in conjunction with
the straight stitch needle plate. The clearance between the needle and the outer edge of
the toe is 1/4” (6 mm) and between the needle and the inner edge of the toe 1/8” (3 mm).
Free-motion/Darning foot (3.0 and 2.0)
Insert the pin of the foot as far as it will go into the hole at the back of the presser foot
holder. The ”C-shaped” guide should be positioned around the presser foot bar. The long
arm must be behind the needle bar. Tighten the screw.
Important: Make sure that the IDT is disengaged when using presser foot 2A, 5A, 5M, 6A and
the free-motion/darning foot.
1:7
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pfaff Expression 3.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pfaff Expression 3.0 in the language / languages: English as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pfaff Expression 3.0

Pfaff Expression 3.0 User Manual - German - 52 pages

Pfaff Expression 3.0 User Manual - Dutch - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info