478157
65
Zoom out
Zoom in
Previous page
1/72
Next page
6363
Sewing problems and their solutions
This machine has been developed with ease of operation in mind. No diffi cult or tricky set tings
need to be made. Sewing problems of the kind described below may occur as a result of minor
adjustment and operating errors. They can be easily adjusted by following the in structions.
Problem Cause Solution
Needle breakage The needle was bent or the
point damaged.
The needle was not fully
inserted.
The fabric was pulled too
rmly.
Insert new needle
(see page 13).
Insert needle fully
(see page 13).
Do not pull on the fabric when
sewing.
Thread breaks Incorrectly threaded.
Thread has caught.
Thread tension is too tight.
Needle not fully insert.
Incorrect needle used.
Thread properly (see page 14 - 23).
Check if the thread is caught on the
spool stand etc.
Correct the tension (see page 46 - 56).
Insert needle correctly (see page 13).
Use needle system EL X 705.
Skipping stitches Needle bent or point
damage.
Needle not fully inserted.
Incorrect needle used.
incorrectly threaded.
Insert new needle (see page 13).
Insert needle correctly (see page 13).
Use needle system EL X 705.
Thread properly (see page 14 23).
Stitch formation
faulty
Incorrect setting of thread
tension.
Re-set thread tensions (see page 46
- 56).
3- or 4-thread
overedge seam has
an irregular
appearance and the
upper looper thread
has not interlocked
in the seam.
The converter is attached. The converter must be removed (see
page 32).
Machine will not
operate although
master switch is on.
Power supply interrupted. Close looper cover (see page 8).
Fabric not neatly
trimmed
Waste thread between
upper and lower blade
Upper blade is blunt.
Clean blades.
Replace upper blade (see page 59).
Puckered seams Thread tension too tight.
Incorrect setting of
differential feed.
Thread has caught due to
incorrect threading
Reduce thread tension.
Re adjust differential feed (see pages
36, 37).
Thread correctly (see pages 14 - 23).
Fabric not fed
through evenly
Stitches too short.
Sewing foot pressure too
low for heavy fabrics.
Sewing foot pressure too
high for lightweight fabrics.
Increase stitch length (see page 38).
Increase sewing foot pressure (see
page 28).
Reduce sewing foot pressure (see
page 28).
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pfaff Coverlock 4852 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pfaff Coverlock 4852 in the language / languages: English as an attachment in your email.

The manual is 5,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pfaff Coverlock 4852

Pfaff Coverlock 4852 User Manual - German - 72 pages

Pfaff Coverlock 4852 User Manual - French - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info