750008
40
Zoom out
Zoom in
Previous page
1/44
Next page
B
A
D
C
40 –MACHINE MAINTENANCE
Replacing the Upper Cutter
Turn off the main power switch and unplug the machine.
The upper cutter should be changed when it becomes
blunt. Change it by following the below instructions. If
you are having any difculties, have a service technician
make the necessary adjustments.
Open the front cover.
Place the upper cutter in its highest position.
Loosen the upper cutter set screw (A) with the
double-ended wrench (use the small end) and remove
the upper cutter (B).
Place a new upper cutter to the upper cutter holder (C)
Tighten the upper cutter set screw (A) partially.
Place the upper cutter in its lowest position.
Adjust the position of the upper cutter until the front
edge of the upper cutter is approx 1-1.2mm lower than
the cutting edge of the stationary cutter (D).
Tighten the upper cutter set screw (A) completely.
Troubleshooting
Machine Does not Run
Possible Cause: Machine not properly connected to power source.
Solution: Check that machine has been properly connected to power source (page 7).
Possible Cause: The safety device is activated.
Solution: Close open covers (page 8).
Fabric Does not Feed Well
Possible Cause: Stitch Length is set too short for the fabric being sewn.
Solution: Increase the stitch length setting (page 26).
Possible Cause: Differential Feed is not set in the correct position for the fabric being sewn.
Solution: Adjust the Differential Feed (page 25).
Possible Cause: Presser foot pressure is not correctly set for fabric being sewn.
Solution: Adjust presser foot pressure (page 25).
Irregular Trimming
Possible Cause: Upper cutter is not in proper position.
Solution: Check alignment of cutters (page 40).
Possible Cause: Cutter is damaged or worn out.
Solution: Replace the upper cutter (page 40).
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pfaff Admire Air 5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pfaff Admire Air 5000 in the language / languages: English as an attachment in your email.

The manual is 7,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pfaff Admire Air 5000

Pfaff Admire Air 5000 User Manual - German - 44 pages

Pfaff Admire Air 5000 User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info