750008
32
Zoom out
Zoom in
Previous page
1/44
Next page
A
B
C
D
32 – SEWING
Using Guide Lines
The guide lines on the top of the front cover help you to
position the fabric while sewing. The numbers/lines indi-
cate the distance from the right needle position in inches.
The cutting width between the right needle position and
the upper cutter when in the standard position is 3.5 mm.
Start Sewing
When the machine is completely threaded, close the
front cover and bring all of the threads over the stitch
plate and slightly to the left under the presser foot.
Ensure that the upper cutter moves against the station-
ary cutter correctly by turning the hand wheel slowly
toward you. If the upper cutter blade does not move
correctly, check if there are any fabric or waste thread
stuck between the blades.
Hold the threads and apply a slight tension.
Turn the hand wheel toward you 2 or 3 complete turns
to start making a thread chain. Check if all threads
wind around the stitch nger of the stitch plate. If the
threads do not wind around the nger, make sure each
thread is threaded correctly.
A. Continue holding the thread chain while pressing
the foot control. Sew until the chain is 2″-3″ (5-8cm)
long.
Place fabric under the front of the presser foot and
sew a test sample. Guide the fabric slightly with
your left hand while sewing. Do not pull on the fab-
ric as this may deect the needle, causing it to break.
B. When you reach the end of the fabric, continue sew-
ing while drawing the finished fabric gently back-
wards and to the left. This is called chaining off. It
prevents the threads from coming undone and pre-
pares for next sewing.
C. Cut the threads with the thread cutter as illustrated,
leaving a thread chain approximately 2″-3″ (5-8cm)
long at the end of the fabric.
Pin Placement (D)
Insert straight pins to the left of the presser foot. The pins
will be easy to remove and are away from the cutters.
Sewing over pins will damage and might destroy the edge
of the cutters.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pfaff Admire Air 5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pfaff Admire Air 5000 in the language / languages: English as an attachment in your email.

The manual is 7,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pfaff Admire Air 5000

Pfaff Admire Air 5000 User Manual - German - 44 pages

Pfaff Admire Air 5000 User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info