478897
17
Zoom out
Zoom in
Previous page
1/24
Next page
Kantenbeschneideinrichtung
-731/01
Dispositif
a
raser
les
bords
-731/01
Edge
trimmer
-731/01
Dispositivo
recortador
-731/01
Dispositivo
tagliamargini
-731/01
Dispositivo
cortador
-731/01
Taste
1
nach
unten
drücken:
Schneideinhichtung
eingeschaltet.
Taste
1
nach
oben
driicken:
Schneideinrichtung
ausgeschaltet.
Achtung:
Nicht
in
das
laufende
Messergreifen,Verletzungs
gefahr!
Messer
auswechseln
Motor
und
Schneideinrichtung
ausschalten.
Schrauben
2
losen
und
Messerauswechseln;
das
Messer
soil
im
unteren
Umkehrpunktca.
1mm
un
ter
der Gegenschneide
stehen
(siehe
Kreis).
Push
control
1
down:
The
trimmer
is
engaged.
Push
control
1
up:
The
trimmer
is
disengaged.
Danger!
Keep
fingers
away
from
moving
knife!
Changing
the
knife
Switch
off
the
motor
and
the
edge
trimmer.
Loosen
screw
2
and
change
the
knife.
When
the
knife
is
at
its
lowest
point,
it
should
be
positioned
abt
1
mm
below
the
stationary
cutting
edge
(see
encircled
view).
Abaisser
Ia
touche
1:
couteau
embraye.
Pousser
a
touche
1
vers
le
haut:
couteau
debraye.
Attention:
Ne
pas
mettre
a
main
dans
le
couteau
en
action.
Risque
d’accident!
Echange
du
couteau
Arrêter
le
moteur
et
debrayer
le
couteau.
Desserrer
Ia
vis
2
et
sortir
le
couteau.
Le
couteau
neuf
devra,
en
position
basse,
se
trouver
é
environ
1
mm
plus
bas
que
le
contre-couteau
(voir
medaillon).
Pulsando
Ia
palanca
1
hacia
abajo,
el
dispositivo
recortador
se
conecta:
pulséndola
hacia
aniba,
se
desco
necta.
Atención:
No
acorque
a
mano
a
Ia
cuchilla
en
marcha.
Peligro
de
accidente!
Camblo
de
Ia
cuchilla
Desconecte
el
motor
ye! dispositivo
recortador.
Afloje
los
tornillos
2
y
cambie
Ia
cuchilla.
La
nueva
cuchilla
deberä
quedar,
en
el
punto
muerto
inferior,
a
1
mm
aprox.
por
debajo
de
Ia
contracuchilla
(v.
circulo).
Per inserire
ii
dispositivo
tagliamargini,
premere
ii
tasto
1
verso
ii
basso:
per
disinserirlo,
premerlo
verso
ii
alto.
Atenzione:
Non
toccare
ii
coltello
funzionante,
rischio
d’incidente!
Cam
bio
del
coltello
Disinserire
ii
motore
ed
ii
dispositivo
tagliamargini,
Allentare
le
viti
2
e
cambiare
ii
coltello.
Cuando
ii
nuevo
coltello
Si
trovi
nel
punto
morto
inferiore,
dovrà
restare
ca.
1
mm
solo
ii
controcolteilo
(vedi
circolo).
Pressionando
a
tecla
1
para
baixo:
o
dispositivo
cortador
estä
ligado.
Pressionando
a
tecla
1
para
cima:
o
dispositivo
estä
desligado.
Atenção:
Nao
colocar
a mao
na
faca,
em
funcionamento.
Perigo
de
acidente!
Troca
de
facas:
Desligue
o
motore
o
dispositivo
cortador.
Soite
os
parafuSoS
2
etroque afaca;
afaca
deveraficara
umadis
tancia
de
aproximadamente
1
mm
abaixo
da
contrafaca
no
ponto
de
inversão
inferior
(veja
circulo).
Fig.
13
F
16298
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pfaff 561 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pfaff 561 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info