478672

Pfaff 130 Manual

8
Zoom out
Zoom in
Previous page
1/22
Next page
To
protect
presser
foot
and
feed,
never
operate
machine
without
placing
fabric
under
the
presser
foot.
With
the
cloth
inserted
and
the
presser
foot
lowered,
turn
the
balance
wheel
toward
you.
At
the
same
time,
give
a
slight
pressure
with
your
knee
against
the
knee
control—or
against
the
foot
control
on
some
portable
models.
7.
To
remove
the
work
Stop
the
machine.
Turn
the
balance
wheel
toward
you
until
the
take-up
(see
section
on
threading
the needle)
is
at
its
highest
point.
(Or
turn
the
wheel
to
complete
the
stitch.)
Raise
presser
foot.
(On
lifting
the,
presser
foot,
the
tension
is
automatically
released.)
Draw
the
cloth
to
the
rear
of
the
needle.
Cut
the
thread
close
to
the
material
on
the
thread
cutter.
8.
To
regulate
the
tension
of
the
upper
thread
The
tension
of
the
upper
thread
is
regulated
by
means
of
tension
nut
(M),
(Fig.
4).
Turning
this
screw
clockwise,
the
tension
will
become
tighter.
Unscrewing
it,
counter
clockwise,
it will
become
looser.
Having
adjusted
the
tension
for
a
certain
kind
of
thread,
(you
con
best
judge
this
tension
for
yourself
by
pulling
the
thread
gently
with
your
hand
when
you
have
threaded
the
machine
through
the
tension
spring),
lust
glance
at
the
number
marked
in
the
bell
behind
the
ten
sion
nut,
and
note
its
relative
position.
If
the
upper
tension
is
too
loose,
the
under
thread
will
pull
down
the
upper
thread,
forming
little
knots
or
loops
as
shown
in
Fig.
8.
If
the
upper
tension
is
too
tight,
the
under
thread
is
drawn
up,
as
illustrated
in
Fig.
9
Fig.
10
shows
the
locking
in
the
two
threads
in
the
center
of
the
material,
as a
result
of
the
proper
adjustment
of
both
tensions.
If
the
tension
is
too
loose,
take
the
bobbin
case
out
of
the
machine
(Fig.
5),
and
tighten
the
small
tension
screw
(Z)
in
a
clockwise
direction
with
the
aid
of
the
screw
driver.
If
the
tension
is
too
tight,
unscrew
it
in
a
counter
clockwise
direction.
(Fig.
11).
10.
To
regulate
the
length
of
stitch
The
length
of
the
stitches
is
regulated
by
the
stitch
regulator
screw.
(Fig.
6).
In
the
zero—(or
neutral)—
posi
tion,
there
is
no
feeding
at
all.
The
numbers
above
zero
ore
for
forward
stitching;
the
space
below
for
reverse
stitching.
Fig.
9
Fig.
10
9.
To
regulate
tension
of
the
under
thread
12
13
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pfaff 130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pfaff 130 in the language / languages: English as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pfaff 130

Pfaff 130 User Manual - German - 30 pages

Pfaff 130 User Manual - Dutch - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info