770983

Petsafe ZIG00-16969 Manual

11
Zoom out
Zoom in
Previous page
1/28
Next page
11
petsafe.com
Double Loop Boundary
• To section off only one boundary area or one
section of your yard (e.g., front property only, or
waterfront property)
• The 2 parallel sections of the double boundary
wire must be separated by a minimum of
approximately 5 ft. from each other in order to
avoid cancelling out the signal as well as provide
an adequate boundary width (3E)
• A double loop layout requires twice as much wire
as a single loop layout because it doubles back
along the same path
With a double loop layout, the boundary wire starts
at the fence transmitter, advances out to the yard and
continues to form a boundary zone in one section
of your property (e.g., front property only). Then the
wire makes a U-turn back along the same path and
connects back to the fence transmitter. This forms a
boundary zone with a double wire.
Sample 3 (3E)
Front Property or Back Property Only
From the fence transmitter, run the wire to point A, then
to point B and so on (B to C to D to E to F). Next, make
a U-turn and follow your path all the way back to point
G, keeping the wire separated by at least 5 ft. When
you get back to the house (G), make a sharp turn along
the side of the house back to point A. Finally, twist
the wires from point A and connect them back to the
fence transmitter.
Sample 4 (3F)
Front Boundary Only
From the fence transmitter, run the wire to point A, then
to point B. Make a U-turn and follow your path back
to point A, keeping the wire separated by at least 5 ft.
Then twist the wires from point A and connect them
back to the fence transmitter.
Sample 5 (3G)
Waterfront Property
From the fence transmitter, run the wire to point A,
then to point B. Make a U-turn and follow your path
to C, then to D, then to E. Next, make another U-turn
and follow the same path all the way back to point
A, keeping the wire separated by at least 5 ft. Finally,
twist the wires from point A and connect them back to
the fence transmitter.
Sample 6 (3H)
Wire Loop Attached to Existing Fence
This layout allows you to include your existing fence
as part of your layout and keep your pet from jumping
out or digging under your existing fence. It reduces
the amount of wire which will need to be buried.
From the fence transmitter run the wire to point A,
then to point B and so on (B to C to D to E to F). Next,
make a U-turn and follow your path all the way back
to point A, keeping the wire separated by at least
5 ft. Finally, twist the wires from point A back to the
fence transmitter.
A
C
D
E
B
5 ft.
3E
3F
3G
3H
A
C
D
E
F
B
5 ft.
A
B
5 ft.
E
F
B
Place Transmitter Inside
A
A
G
G
D
C
5 ft.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Petsafe ZIG00-16969 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Petsafe ZIG00-16969 in the language / languages: English as an attachment in your email.

The manual is 3.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info