770963

Petsafe PPA00-10862 Manual

5
Zoom out
Zoom in
Previous page
1/49
Next page
5
DEITNL
ES
FR
EN
Accessories available online
Installation – Metal or Metal Core Doors
Installation of the cat flap into a door containing metal will require an Installation
Adaptor (sold separately) to ensure proper performance. Once this has been
purchased, follow the instructions below.
1. Attach the supplied Cutting Template to the outside of your door in the
correct position ensuring that it is the right way up and level (Fig. C).
2. Drill four corner holes with a 12 mm (½”) diameter drill bit as marked on
the Cutting Template through the door. Ensure that the drill remains straight
and level.
3. Using a jig or key-hole saw, cut along the appropriate line as indicated
on the Cutting Template. (Fig. D).
4. Clean the area of any dust, dirt or debris.
5. Slide one installation adaptor plate over the tunnel on the interior frame of
the cat flap.
6. From the interior of the home, insert the cat flap interior frame with
installation adaptor into the opening.
7. From the exterior of the home, place the remaining installation adaptor
plate onto the interior frame tunnel followed by the exterior frame of the
cat flap.
8. Making sure to center the cat flap in the hole. Three (3) different lengths
of screws have been provided with this cat flap. Select the appropriate
length. Using a manual screw driver, screw the exterior frame to the
interior frame.
9. Insert the 8 blanking plugs into the exterior and interior installation
adaptor plates and 2 blanking plugs into the exterior frame.
10. Remove the batteries from the cat flap and wait for 30 seconds. Re-install
the batteries and battery cover. The cat flap is ready to use.
Optional: For additional support use screws that are less than half the
thickness of your door to attach the installation adaptors to the door.
Installation – Walls
Installation of the cat flap into a wall will require an Installation Adaptor (sold
separately) to ensure performance. Extension Tunnels may also need to be
purchased to ensure that the flap extends completely through the wall. Once
this has been purchased, follow the instructions below.
Important: Check for electrical and plumbing that could be in
the wall where you wish to place the pet door.
1. Attach the supplied Cutting Template to the inside of your wall in the correct
position ensuring that it is the right way up and level (Fig. C)
Note: Depending on the presence of metal, there are two (2) options on the
cutting template. Please use the appropriate line for your wall construction.
2. Drill four corner holes with a 12 mm (½”) diameter drill bit as marked on the
Cutting Template through the wall. Ensure that the drill remains straight and level.
3. Using the appropriate tool for your home construction, such as a jig saw, cut
along the appropriate line as indicated on the Cutting Template. (Fig. D).
4. From the exterior of the home, finish cutting the hole through the wall using
the four corner holes drilled through the wall as a guide.
5. Clean the area of any dust, dirt or debris.
6. Slide one installation adaptor plate over the tunnel on the interior frame
and attach it to the back of the frame using the two (2) pan headed
screws (included).
7. From the interior of the home, position the interior assembly on the wall
and mark the four (4) screw holes on the installation adaptor plate
attached to the cat flap. Remove the assembly.
8. Using the proper hardware for your wall construction (not included), drill
the appropriate size holes for your hardware and attach the interior frame
with installation adaptor to the wall.
Optional: Add tunnel extensions (sold separately) to extend the tunnels
through your wall.
9. Attach the two (2) included metal clips into the rectangular recesses on
the remaining adaptor plate with the flat side of the clip flush with the outer
face of the plate.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Petsafe PPA00-10862 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Petsafe PPA00-10862 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5.29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info