Manual Petsafe PIG00-11116 (page 8 of 19) (English)

770992

Zoom out

Zoom in

1/19

petsafe.com1-800-732-2677 1514

Step 6: Connect the Wires

Now that the boundary wire has been positioned and spliced, the

next step is to connect the wire from inside to the surge protector, and

then to the transmitter.

1. Strip 3⁄8 in. of insulation from the 2 ends of the boundary wires in

order to connect them to the surge protector (6A).

2. Insert the stripped ends into the 2 left red connector holes on the

bottom of the surge protector labeled “LOOP” (6B). Make sure the

copper ends do not touch each other at the terminals.

3. Next, connect the surge protector to the fence transmitter with 2

twisted wires. Measure and cut 2 lengths of wire, then strip 3⁄8 in. of

insulation at both ends from each.

4. Insert the 2 ends of the wires into the 2 black connectors at the

bottom of the surge protector labeled “TRANSMITTER.”

5. Next, insert one wire into the red tab on the bottom of the

transmitter and insert the other wire into the black tab.

6. Plug the fence transmitter adapter into the outlet on the surge

protector. You are now all connected (6C).

7. Turn the fence transmitter on by sliding the power switch to the

up position.

A green light means you have a continuous loop. If an alarm sounds

and a red warning light illuminates, it means that you do not have a

continuous loop. Make sure the wires are in the terminals and that all

connections are complete. And if you get stumped, you can always

check out our troubleshooting section, watch one of our instructional

videos or give us a call.

Verify that the boundary loop and transmitter wires are connected to the proper surge protector terminals. Reversed

connections will result in an increased risk of surge-related damage.

Step 7: Prepare the Receiver Collar

In order to test the system you will need to use the receiver collar. Your

receiver collar comes installed with short contact points. If your pet has

long or thick hair, use the long contact points instead. Tighten or switch

the contact points by using the contact point wrench (7A).

Turn On the Receiver Collar

The collar will automatically turn on whenever it is removed from the

charger. To turn on the receiver collar when it is not on the charger,

press and hold the mode button for 1 second (7B). Avoid touching the

metal contact points.

Next, the indicator light will flash green once and then go off for

1 second. It will then come back on and glow continuously for 5

seconds—either solid red, solid green, or red+green together to

indicate the status of the battery (7C). Finally, there will be a series

of red flashes which represent the static correction level. This quick,

opening series of tests is part of the ReadyTest® startup feature. The

receiver collar will then automatically start the PerfectFit test by flashing

red+green together every second for 90 seconds.

A B

Boundary

Wire Transmitter Wires

Contact

Point

Mode

Button

ReadyTest® Feature

The ReadyTest® startup feature lets you know the status of the battery as

well as the current correction level of the receiver collar. It also checks

that all circuits are working correctly. This mode automatically starts

every time you remove the receiver collar from the charger, or first turn

it on. If the receiver collar is on your pet during the ReadyTest® startup,

the test will fail and the receiver collar will automatically turn off. This

also means the system will not contain your pet!

If the receiver collar fails the ReadyTest® startup, the receiver collar is automatically turned off; your pet will not be contained.

If the ReadyTest® feature does detect a problem, the receiver collar

will continually beep and the indicator light will glow solid red for

20 seconds. The receiver collar will automatically turn off. Do not

put the receiver collar on your pet at this time; your pet will not be

contained. Instead, turn the receiver collar back on and repeat the

test. If the receiver collar continues to fail the ReadyTest® startup, call

the Customer Care Center.

PerfectFit Test

This test is an added feature to verify a “perfect” fit of the collar

around your pet’s neck; however, it is not required for the system to

function. After the ReadyTest® statup finishes with the series of red

flashes that correspond to the static correction, the receiver collar will

automatically start the PerfectFit mode. For 90 seconds the receiver

collar will continually flash red+green together. You must place the

receiver collar on your pet and adjust the fit within the 90 seconds or

it will go back to normal operation mode and flash the status of the

battery (red, green, or red+green together) every 4 seconds.

After you adjust the collar on your pet and the contact points are

touching his or her skin (or if you inadvertently touch both of the

contact points with your fingers), the receiver collar will emit a unique

double tone. You will know you have the proper fit after you hear

5 consecutive double tones and you see 5 green flashes. Then the

receiver collar moves into normal operation mode and flashes the

status of the battery every 4 seconds.

Turn Off the Receiver Collar

To turn off the receiver collar, press and hold the mode button

continuously for 5 seconds until the red light turns off. To extend the

time between charging the receiver collar, consider turning off the

receiver collar when it is not in use.

Set the Static Correction Level

The static correction levels increase in strength from 2 to 6, with level

1 being tone only (no correction), and level 6 being the maximum

setting. Refer to the table to the right to choose the static correction

that best fits your pet.

To set or check the static correction, press and hold the mode button

until you see a red light. Then let go. The collar will then emit a series

of red flashes that correspond to the current correction level (e.g., 4

red flashes means level 4). Press and hold the mode button again

for 1 second to increase the level by one setting. You must count the

number of red flashes to determine the level setting.

Note: Once you count 6 red flashes you are at level 6, and an

additional hold will cycle the receiver collar back to level 1, which is

tone only.

Refer to the table “Receiver Collar Status Indicators” on page

29 for a complete guide to all the status lights and tones for the

receiver collar.

Receiver

Indicator Light

Static Correction Level Table

LevelIndicator Light Static Correction

1 1 red flash None—tone only

2 2 red flashes Low

3 3 red flashes Medium-low

4 4 red flashes Medium

5 5 red flashes Medium-high

6 6 red flashes High

LOOP TRANSMITTER

BOUCLE ÉMETTEUR

Push Tab

Down to

Insert Wire

³⁄₈ in.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Petsafe PIG00-11116 in the language / languages: English as an attachment in your email.

The manual is 3.48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Petsafe PIG00-11116 Manual

Product: