770988
7
Zoom out
Zoom in
Previous page
1/24
Next page
www.petsafe.net 7
Operating Guide
Step 1: Set Up the Transmitter
Important: You may need to move the Transmitter several times before determining the final location. The Transmitter is located
at the exact center of the Pet Area.
Place the transmitter:
At least 2 feet above the floor located on the ground floor of your home.
In a dry, well ventilated, protected area.
In an area where temperatures do not fall below -10°F (-23°C).
Mounted to a wall, on a non-metal table or other hard surface to ensure proper ventilation (1A).
At least 3 feet from large metal objects, as these items may reduce the size and shape of your Pet Area (1B). Placing the Transmitter inside
a metal building or shed can reduce the maximum range of the system.
Do not place anything on top of Transmitter or cover any ventilation holes. This may overheat the Transmitter and cause
early transmit failure.
Do not place Transmitter in a closet or any other confined, unventilated area.
Do not place Transmitter on a metal surface.
Wall Mount the Transmitter
1. Place bracket against the wall in position to be hung (1D).
2. Mark the hole locations.
3. If mounting directly to the wall studs, drill 1/16 inch pilot holes for the screws. Anchors would not be needed. If mounting to dry wall using
the mounting anchors, drill 1/4” holes and insert anchors completely into the holes.
4. Screw bracket to the wall.
5. Place the bottom edge of transmitter against the bracket making sure the screw recesses are over the bracket hooks on both sides.
6. Rotate transmitter up and push firmly until the top latch locks into place (1E).
To maximize your Pet Area, make sure the Boundary Switch is on “+” and the Boundary Control Dial is set to “8” (1C). Plug Power Adapter into
Power Jack and standard 120 volt outlet. Turn the Transmitter ON.
The Transmitter has a built in Power Loss Alarm. This alarm sounds an intermittent tone alarm indicating power has been removed from the
Transmitter. The alarm will sound for at least 20 minutes. If power is removed from the unit, your pet is no longer contained.
There are two ways to turn off the Power Loss Alarm:
1. Plug the power cord back into a functional 120 volt outlet. The unit assumes power has been suspended because of an accident such as a
child unplugging the cord, thus sounding the tone.
2. Unplug Transmitter Power Adapter from the Power Jack located on the bottom of the Transmitter, indicating power is intentionally being suspended.
When your power is restored, be sure to reconnect the Power Adapter into the Power Jack of your Transmitter.
3ft.
Wall
Mount
Tabletop
1A 1B 1C 1D 1E
Mounting
Bracket
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Petsafe PIF00-15001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Petsafe PIF00-15001 in the language / languages: English as an attachment in your email.

The manual is 2.14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info