770985
12
Zoom out
Zoom in
Previous page
1/24
Next page
12 +1 (800) 732-2677
Step 4: Adjust the Pet Area to Desired Size
Make sure the entire pet area lies within your property boundaries (4A). Always start determining the boundary zone
at the shortest distance from transmitter. Place the boundary switch on “Low” if the boundary zone will be less than
45 feet from the transmitter.
Test Light Instructions
1. Make sure the receiver collar battery is properly charged.
2. Set the correction level to 2 or above.
3. Hold the test light contacts to the contact points. (4B)
4. Walk toward the boundary zone holding the receiver collar about waist high
until the test light flashes (
4C
).
Save the test light for future testing.
Note: If your next-door neighbor has a containment system, see the troubleshooting section page 18.
To maximize your pet area, make sure the boundary switch is on “High” and the boundary control dial is set to “8”. Plug
the power adaptor into the power jack and a standard 120 volt outlet.
Two-Person Method
Hold the receiver collar about waist high with logo side facing away from the transmitter and contact points facing
upwards. Walk to the edge of the desired pet area. Facing away from the transmitter, hold the receiver collar at the
edge of the desired pet area (4C).
Starting with the boundary control dial set to “8, have a second person turn the dial down SLOWLY. When the
receiver collar tone starts, tell the person to stop turning the boundary control dial. Walk back into the pet area until the
receiver stops sounding. Verify the pet area boundary by walking towards the boundary zone and verifying that the
tone/test light flashes begin at the desired location. Test at multiple locations around the pet area to verify the pet area
is within your desired location. Record your settings on page 13 for future reference.
One-Person Method
Measure the shortest distance from the desired boundary zone to the transmitter. Find the distance on the transmitter range
chart on page 13 and set the boundary switch and boundary control dial. Hold the test light contacts to the contact
points (4B). Take the receiver collar to the boundary zone with the logo side facing away from the transmitter and contact
points facing upwards (4C). Hold the receiver collar about waist high until the receiver collar tone sounds and the test light
flashes. If the receiver collar tone sounds before or after the desired boundary zone, return to the transmitter and adjust
the boundary control dial. Repeat this process until the receiver collar tone sounds at the desired location. Record your
settings on page 13 for future reference.
Pet
Area
B
o
u
n
d
a
r
y
Z
o
n
e
Pet Area
Street
4A 4B 4C
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Petsafe PIF00-12918 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Petsafe PIF00-12918 in the language / languages: English as an attachment in your email.

The manual is 1.79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info