Petporte smart flap® Installation Into a Non-Glass Door
1. Attach the supplied Cutting Template to the outside of your door in the selected position ensuring that it is the right way up and is level.
2. Drill the two holes with a 7 mm-diameter drill bit as marked on the Cutting Template into the house door.
3. Cut out the large hole as marked on the Cutting Template by the dashed line. When cutting this hole, keep to the outside of the dashed line to ensure that
there is clearance for the Extension Tunnel.
4. Clean the area from any dust, dirt, or debris.
Note: Follow Steps 5-9 if you completed the assembly instructions (for testing) on page 7.
5. If the low voltage power supply is plugged in to the mains, unplug it.
6. Remove the interior four self-tapping fixing screws, the large interior cover plate, and transparent door.
7. Remove the two M6 screws, which hold the exterior and the interior sections together.
8. Remove the battery, if attached.
9. Unplug the porch cable connector from the electronics board.
10. Mount the interior section through the hole with any additional Extension Tunnel sections that are required. (see Figure 11)
11.Feed the Porch Cable from the porch and external section through the door and through the rectangular opening on the interior section. Mount the exterior
section on the outside of the door over the Extension Tunnel.
12. Put the supplied M6 screws through the exterior section and screw into the interior section. Please note depending on the thickness of your door you may
need to cut the screw length down.
13. Push the Porch Cable connector onto the electronics board. Any excess cable must be routed to the right of the battery compartment. Ensure the cable
does not lay on top of the electronics board. (see Figure 12a and 12b)
14. If you require an extension lead, then plug it into the electronics board rather than the power supply. The provided power supply then connects in the
extension lead.
15. If you do not require an extension lead, attach the power cable to the power connector on the electronics board. Route the cable along the cable guides
so that the wire passes through one of the slots at the bottom of the Cat Flap closest to the mains power supply.
16. Replace the transparent door flap ensuring that the ridge around the door is facing inward.
17. Reattach the interior large cover plate using the four self tapping fixing screws.
18. If a battery is to be used as an alternative or in addition to the mains power supply then attach a 9-volt (IEC 6LR61) battery and insert into the battery
compartment within the internal section. Click the small cover plate into place over the battery compartment.
19. When the installation of your Petporte smart flap® is completed, place the two blanking plugs over the screws on the exterior frame and the four blanking
plugs on the interior frame. (Figure 13)
20. If you select not to use the Petporte smart flap® utilising battery power alone, plug in the power supply. Your Petporte smart flap® is now ready to use.
Petporte smart flap® Installation Into Glass Doors or Windows
The Petporte smart flap® is also designed for installation into glass and requires a circular hole of diameter 212 mm. Working with glass is a skilled job and
should be carried out by a professional glazier. Your glazier will need to cut a circular hole of diameter 212 mm as per the glass template. If you are in any
doubt then please consult with your glazier about the fitting of the Petporte smart flap®. Once a suitable opening is formed, then install Cat Flap as described
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Petsafe Petporte smart flap - Microchip 100 series at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Petsafe Petporte smart flap - Microchip 100 series in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.
The manual is 5.88 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
Others manual(s) of Petsafe Petporte smart flap - Microchip 100 series
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
