782706

Pet-Mate Dog-Mate 216 Dog door Manual

2
Zoom out
Zoom in
Previous page
1/4
Next page
2
4
6
5
3
1
DOOR THICKNESS
+ 3/4” (19mm)
DOOR THICKNESS
+ 3/4” (19mm)
3/8” (10mm)
3/8” (10mm)
3/8”
(10mm)
3/8”
(10mm)
•Read all instructions before installing or using this product.
•Register your purchase on-line at www.pet-mate.com (see guarantee).
•Do not allow children to play with this product.
•This door is not designed to prevent the passage of children or small adults in either direction.
•Inspect product regularly for correct operation and damage. Do not use if in doubt.
•This product is designed for use with pets only, as described in these instructions.
•The locking system of this pet door is not intended as a security device.
•This pet door is not a fire resistant door and must not be used where there is a risk from
fire spread.
•The installer of this pet door is responsible for complying with all relevant building regulations.
•During installation of this pet door take appropriate care. Follow safety instructions for all tools
and wear appropriate personal protective equipment.
•Dispose of all packaging material properly.
NOTE: Plastic bags could cause suffocation - keep
away from children and animals.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Hereby, Pet Mate Ltd., declares that this product is in compliance with the essential requirements
and other relevant provisions of EU Directives. All Declarations of Conformity (DoC) may be viewed
at www.pet-mate.com/eudoc.
1. Remove locking panel from interior frame by simultaneously depressing the button marked 'PRESS'
and lifting up. Place frame in required position where it will not be exposed to prevailing winds with tape
as in Fig. 1. Note that the bottom of the aperture should be approximately level with your dogs stomach.
Mark position of mounting bolt holes and draw around the aperture with a sharp pencil. Remove frame
from door.
2. Drill bolt holes with a 1/4" (6mm) diameter drill taking care to keep the drill square (Fig. 2.) Note that for
installation in walls and doors more than 2" (50mm) thick we recommend that you attach the frames
using suitable screws (not supplied) and drill holes to suit.
3. Mark a cutting line 3/8" (10mm) outside the aperture drawn in Fig. 1 and drill a hole approximately 1/4"
(6mm) diameter within each corner as in Fig. 3. Cut out along the cutting line with an electric jigsaw or
similar tool taking care to cut square to the door.
4. Measure thickness of your door and using a sharp knife or scissors cut along the nearest guideline on
the four door liners to door thickness PLUS 3/4" (19mm). Do not trim off the notch(es) on the bottom
door liner (Fig. 4.) Also cut the mounting bolts supplied to your door thickness + 3/4" (19mm) using a
hacksaw as in Fig. 4 and file bolt ends for easy nut threading. For walls and doors greater than 2"
(50mm) thick we recommend that you cut your own door liner using suitable 3/32" (2mm) metal sheet
(not supplied).
5. Assemble 4 door liners into the slots provided in the exterior frame and tape temporarily in position as
shown in Fig. 5. Note that the 'notched' door liner is fitted to the bottom of the frame with the notch(es)
around the frame magnet(s). The door liners should be fitted with their smooth face innermost. Push
rubber seal supplied into groove in exterior frame as shown, leaving a drainage gap at bottom centre.
6. With the aid of a helper assemble dog door in position with tape ensuring that door liners locate properly
into interior frame, then fit nuts and bolts as shown in Fig. 6. Do not overtighten the fixing bolts. Check
flap swings freely. If it does not, check frames are undistorted and that interior frame is aligned with
exterior frame. Finally, cover fixings with the plastic caps supplied and remove temporary fixing tape.
7. For added security the 2 plastic pins should be inserted through the holes at the bottom of the interior
frame into the locking panel.
CLEANING
Clean using water only. Detergents and polishes may damage the plastic.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pet-Mate Dog-Mate 216 Dog door at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pet-Mate Dog-Mate 216 Dog door in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0.13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info