782704
2
Zoom out
Zoom in
Previous page
1/2
Next page
IMPORTANT:
Program and test microchip cat flaps BEFORE installation
Read safety warnings supplied with your cat flap before installation
1. GLASS PANEL INSTALLATION
Fig. 1. We recommend that you ask a glazier to cut a hole of 263mm (103/8”)
diameter in the position required. (We recommend the bottom of the hole is
approximately level with your pet’s stomach.) For existing toughened/double/triple
glazing, a new glass panel will be required.
Fig. 2. Assemble flap after fitting exterior frame seal (X) supplied with cat flap
and external adapter seal (Y).
Select four screws as follows:
Fully push home the six screw hole covers each side.
2. WALL INSTALLATION
Fig. 3. Mark rectangular hole 182mm (73/16”) wide by 207mm (81/8”) high in
desired position on wall. We recommend bottom of aperture is approximately
level with your pet’s stomach.
Cut aperture to drawn line using suitable tools.
Fig. 4. Fit 4 screw inserts to each adapter. Fit adapter seal (Y) to adapter for use
externally.
Fig. 5. Fit seal (X) supplied with cat flap to exterior frame. Screw exterior frame
to adapter using 12mm (1/2”) screws.
Fig. 6. Carefully drill out 4 mounting holes of interior frame to 5mm (3/16”) diameter.
Fig. 7. Screw interior frame to adapter with 19mm (3/4”) or 22mm (7/8”) screws.
Fig. 8. Trial fit cat flap assembly to interior wall using tunnel adapter (A) and
appropriate number of 50mm (2”) wall liners (B).
Fig. 9 and 10. Fit adapter plates using appropriate screws and wall plugs (not
supplied).
If completely happy with the trial assembly you may secure the tunnel adapter to
the cat flap tunnel and the tunnel sections using heavy duty weatherproof
adhesive tape over the outer joints.
Cover screwheads with covers supplied.
Available separately from your cat flap supplier or direct from Pet Mate, Product
Ref. 308W.
WICHTIG:
Mikrochip-Katzenklappen unbedingt VOR dem Einbau programmieren
und testen
Vor dem Einbau die mit Ihrer Katzenklappe bereitgestellten
Sicherheitswarnungen lesen
1. EINBAU IN GLASSCHEIBEN
Abb. 1. Wir empfehlen, dass Ihnen in diesem Fall ein Glaser den Türeinschnitt
ausschneidet, und zwar an der gewünschten Stelle mit einem Durchmesser von 263mm.
(Es empfiehlt sich, dass der untere Lochrand ungefähr in gleicher Höhe wie der Bauch
Ihres Haustiers ist.) Bei bestehender Sicherheits- bzw. Doppel-/ Dreifachverglasung ist
eine neue Scheibe erforderlich.
Abb. 2. Die Klappe nach dem Anbringen der mit der Katzenklappe mitgelieferten
Außenrahmendichtung (X) und der Außenadapterdichtung (Y) zusammenstellen.
Vier Schrauben wie folgt wählen:
Die sechs Schraubenlochkappen an jeder Seite voll eindrücken.
2. WANDEINBAU
Abb. 3. Rechteckigen Ausschnitt von 182mm Breite mal 207mm Höhe in der
gewünschten Position an der Wand markieren. Es empfiehlt sich, dass der untere Rand
der Öffnung ungefähr in gleicher Höhe wie der Bauch Ihres Haustiers ist.
Den Ausbruch entlang der angezeichneten Markierung mit entsprechenden Werkzeugen
herstellen.
Abb. 4. Vier Schraubeneinsätze an jedem Adapter anbringen. Die Adapterdichtung (Y)
am außen verwendeten Adapter anbringen.
Abb. 5. Mit der Katzenklappe mitgelieferte Dichtung (X) am Außenrahmen anbringen.
Den Außenrahmen an den Adapter mit 12mm Schrauben anschrauben.
Abb. 6. Vier Befestigungslöcher am Innenrahmen sorgfältig auf 5 mm Durchmesser
aufbohren.
Abb. 7. Mit 19mm oder 22mm Schrauben den Innenrahmen an den Adapter schrauben.
Abb. 8. Die Katzenklappe-Baugruppe probeweise mit dem Tunneladapter (A) und der
entsprechenden Anzahl von 50mm Wandauskleidungen (B) an der Innenwand
befestigen.
Abb. 9 und 10. Adapterplatten werden mit entsprechenden Schrauben und
gegebenenfalls mit Wanddübeln befestigt (nicht mitgeliefert).
Nach zufriedenstellender Probemontage, können der Tunneladapter am
Katzenklappentunnel und die Tunnelauskleidungen mit starkem wetterfestem Klebeband
uber die Außenfugen umklebt werden.
Die Schraubenköpfe mit den mitgelieferten Kappen abdecken.
Separat bei Ihrem Katzenklappen-Fachhändler oder direkt von Pet Mate erhältlich,
Produkt-ref. 308W.
Pet Mate Ltd. erklärt, dass dieses Produkt den grundlegenden Anforderungen und anderen
zutreffenden Bestimmungen von EU-Richtlinien entspricht. Alle Konformitätserklärungen
können unter www.pet-mate.com/eudoc aufgerufen werden.
Hereby, Pet Mate Ltd., declares that this product is in compliance with the essential
requirements and other relevant provisions of EU Directives. All Declarations of
Conformity (DoC) may be viewed at www.pet-mate.com/eudoc.
Glass panel thickness (t) Screw length
3mm to 19mm (1/8” to 3/4”)
19mm to 32mm (3/4” to 11/4”)
Over 32mm (11/4”)
50mm (2”)
70mm (23/4”)
(t) + 38mm (11/2”) - not supplied
Glasscheibendicke (t)
3mm bis 19mm
19mm bis 32mm
Über 32mm
Schraubenlänge
50mm
70mm
(t) + 38mm - nicht geliefert
approx.
125mm (5”)
Ø
263mm
(10
3
/
8
”)
1
X
Y
2
Height
207mm
(8 1/8”)
Width
182mm
(7 3/16”)
3Y
4X
5
Ø
5mm
(
3
/
16
”)
6
7
B*
A
8 9
O
U
T
S
I
D
E
I
N
S
I
D
E
B*
A
10
D
*
*
*
*
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pet-Mate Cat-Mate 361 Cat Flap at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pet-Mate Cat-Mate 361 Cat Flap in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info