Manual Peruzzo Padova steel 378 (page 3 of 8) (English, French, Italian, Spanish)

807436

Zoom out

Zoom in

1/8

3/8

Assemblare le cinghie sul portabici come da

facendo attenzione al giusto verso di entrata

nella fibbia

, e al corretto posizionamento delle

cinghie F1 superiori, F2 laterali (se presen-

ti), F3 inferiori,

. Verificare la tenuta delle cinghie

strattonandole.

Attenzione

Prima dell’assemblaggio delle cinghie, consultare la

lista adattabilità auto a disposizione nel punto vendita

e verificare la necessità dell’utilizzo dell’adattato-

re I. La lista specifica il numero e la posizione

( F1-F2-F3 ) che l’eventuale adattatore I deve avere

sulla vostra auto. Se l’adattatore I non è incluso nella

confezione del portabici, acquistarlo separatamente

presso il rivenditore. Una volta determinato lo schema

di montaggio dell’eventuale adattatore I, montarlo

in sostituzione del gancio G,

MONTAGGIO CINGHIE

Assemble the straps on the bicycle carrier as shown in

and

, paying attention to the correct direc-

tion, of entry in the buckle

and correct position-

ing of the upper straps F1, side straps F2 (if pre-

sent), and lower straps F3,

. Check the hold of the

straps by pulling on them.

Important:

Before fitting the straps, consult the car adaptability

list available at the sales outlet and check if adapt-

er I has to be used. The list specifies the number and

the position ( F1-F2-F3 ) that the possible adapt-

er I must have on your car. If adapter I is not includ-

ed in the bicycle carrier package, purchase one sepa-

rately from the dealer. After establishing the assembly

layout of the possible adapter I, fit it in place of the

clasp G,

and

FITTING THE STRAPS

Ensamblar las correas en el portabici como en fig.

, poniendo atención en la manera correcta de

introducirlas en la hebilla

, y en el correcto posi-

cionamiento de las correas F1 superiores, F2 latera-

les (si están), F3 inferiores,

. Verificar que las correas

estén firmemente sujetas, tirando de las mismas

Atención

Antes de ensamblar las correas, consultar la lista de

adaptabilidad al coche, disponible en el punto venta y

comprobar si es necesario utilizar el adaptador I. La

lista especifica el número y la posición ( F1-F2-F3 )

que el eventual adaptador I debe tener en tu coche.

Si el adaptador I no viene incluido en la confección

del portabici, puedes adquirirlo por separado en el

punto venta. Una vez determinado el esquema de

montaje del eventual adaptador I, montarlo en susti-

tución del gancho G,

MONTAJE CORREAS

I GB E

MONTAGGIO PORTACICLO

1. Se necessario, seguire la figura

per assemblare i

binari portabici al tubo D e la figura

per fissare

gli appoggi in gomma P e X.

2. Controllare il perfetto avvitamento di bulloni e dadi

di assemblaggio, eventualmente avvitarli nuova-

mente.

3. Regolare gli archi con la triangolazione che più si

avvicina alla sagoma della vostra auto, come da

esempi forniti in

e consultare la lista

adattabilità auto.

4. I binari reggiciclo devono essere regolati con un’an-

golazione minima di 10 gradi verso l’alto, rispetto al

piano orizzontale,

5. Bloccare fortemente i rocchetti con il pomello (o la

leva, a seconda del modello) e assicurarsi che i denti

siano perfettamente accoppiati, figure

10a

6. In caso si viaggi senza biciclette richiudere l’arco

portabinari verso l’alto,

BICYCLE CARRIER INSTALLATION

1. If necessary, follow figure

to assemble the

bicycle carrier bars on pipe D and figure

for

fixing the rubber supports P

and

2. Check the perfect tightness of the assembly bolts

and nuts, and retighten if necessary .

3. Adjust the arches with a triangulation as close

as possible to the shape of your car, as shown

in the examples provided in fig.

and consult the car adaptability list.

4. The bicycle holder bars must be adjusted with an

upward angle of at least 10 degrees to the horizon-

tal, fig.

5. Tighten the sprockets hard with the knob (or the

lever according to model) and make sure the teeth

are perfectly coupled,

10a

6. When travelling without bicycles close the bar

holder arch upwards,

MONTAJE PORTABICI

1. Si necesario, seguir la figura

para ensamblar las

barras del portabicicleta al tubo D y seguir la figura

para sujetar los soportes de caucho P y X.

2. Controlar el perfecto atornillado de pernos y de tuer-

cas de ensamblaje, y si fuera necesario, atornillarlos

de nuevo.

3. Regular los arcos con la triangulación que más se

asemeje al perfil de tu coche, como se explica en las

y consultar la lista de adaptabilidad

al coche.

4. Las barras que sostienen la bici se tienen que regular

con un ángulo mínimo de 10 grados hacia arriba, con

respecto al plano horizontal,

5. Bloquear firmemente los carretes con la perilla (o la

palanca, según el modelo) y comprobar que los dientes

estén perfectamente acoplados,

10a

6. En caso de viajar sin bicicleta, cerrar el arco portaba-

rras hacia arriba,

6 8 97

10a

OKOK

P1200047-00_378_PADOVA STEEL_21/02/18

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Peruzzo Padova steel 378 in the language / languages: English, French, Italian, Spanish as an attachment in your email.

The manual is 9.77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Peruzzo Padova steel 378

Peruzzo Padova steel 378 Additional guide - All languages - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Peruzzo Padova steel 378 Manual

Product: