720265

Perel FT30C-FR Manual

5
Zoom out
Zoom in
Previous page
1/42
Next page
FT10C/FR - FT15C/FR - FT30C/FR
V. 03 – 11/09/2017 5 ©Velleman nv
Connection
1. Connect the gas hose to the heater without forcing.
2. Install the pressure regulator on the gas cylinder.
3. Check if the connection of the pressure regulator is correctly sealed according to the used gas cylinder.
4. Open the valve of the gas cylinder or the pressure regulator if the gas cylinder does not feature a valve.
5. Check if the connection are correctly sealed using soapy water: soap bubbles may point to a gas leak.
Never test for gas leaks with an open flame.
The connections may have a left-handed screw thread. Consequently, they are threaded in a anticlockwise
direction.
Check if there is a clamp between the pressure regulator and the gas cylinder.
It is allowed to interconnect multiple gas cylinders to increase the fuel autonomy.
The feeding pressure is obtained through the pressure regulator and corresponds to the data on the
specifications table.
Only use certified replacement gas hoses.
It is recommended to use gas cylinders of 30 kg providing a thermal power of 30 kW. You are allowed
to use larger gas cylinders if more thermal power is needed.
It is recommended to use gas cylinders with an appropriate capacity to avoid problems due to partial
fuel gasification. The correct pressure (refer to the specification tag on the heater) is indicated by the
included pressure regulator or a similar model.
Make sure the feeding gas hose is in perfect condition. Only use flexible and appropriate models when
replacing the gas hose. Always respect the local regulations. Do not crimp the flexible hose.
6. Connection to the Mains
Before connecting the heater to the mains, check if the used power supply and frequency match the
specifications on the specification tag. Always respect the local regulations when connecting the heater to the
mains.
Only connect the device to an earthed mains.
Disconnect the device from the mains prior to any maintenance or cleaning activity.
Always make sure that the mains is earthed.
7. Switching On the Heater
1. Open the gas valve.
2. Flick the switch to position I.
3. Fully press and hold the gas valve. Operate the igniter several times.
4. The flame burns. Hold the gas valve pressed for 15 seconds to activate the safety mechanism.
5. Release the gas valve. The flame will keep burning.
The safety mechanism will automatically switch off the heater in a few seconds in case of an electric power
failure. This mechanism will also switch off the heater in case of a gas shortage. In both cases, follow the
explanation above to switch on the heater again.
6. Regulate the gas flow.
7. Avoid operating the igniter for a prolonged period. Check for problems if the heater does not switch on.
8. Checking a Switched-On Heater
Check a switched-on heater by observing the pilot flame at the air exit of the heater. Make sure that the pilot
light burns steadily inside the burner.
Be careful when checking the pilot light as the air exiting the heater can be extremely hot. Maintain
yourself at a safe distance.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Perel FT30C-FR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Perel FT30C-FR in the language / languages: English, German, Dutch, French, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info