130167

Pelgrim lsk 900 Manual

13
Zoom out
Zoom in
Previous page
1/30
Next page
Use
See fig. 1 and 2.
After installation
When the hood is switched on for the first
time, it runs through a phase of reset and self-
checking. At the end of this phase a stand-by
phase will be reached: motor and lamps will
be switched off and teh display will show its
lower segment.
Switching on
The hood is switched on by pressing switch
(1). The motor will not run and the display will
show 0. The motor is set in motion by pressing
button (4) , the display will show 1.
Change the speed by pressing switch (3) or
(4). The speed is decreased or increased by
one step. Continuous pressure on switches (3)
and (4) at the same time for more than 2
seconds causes the motor to work at its
highest speed for 4 minutes. The display
shows a
9 blinking. After that the hood will
return to the stand-by mode.
Switching off
Pressing switch (1) turns the motor off and the
hood will return to its stand-by mode. When
the hood is switched on again, the motor
resumes operation at the previously selected
speed.
Using the hood in recirculation mode
After the reset phase, the motor speed is set
for use in exhaust mode. In order to select the
recirculation mode, the following steps must
be taken: pressing switch (4) in the stand-by
mode shows A on the display. This stands for
selection of the exhaust mode. Pressing
switch (3) and (4) at the same time, while on
stand-by, changes operation to recirculation
mode. The display shows F. Any further
pressing of switch (3) and (4) at the same time
will select the exhaust mode of operation.
Replacing carbon filters
The carbon filter must be used if the cooker
hood is not connected to a duct (see
extraction systems on page 8).
Note:
■ The carbon filter must be replaced at least
twice a year, depending on how much the
cooker hood is used.
■ Carbon filters cannot be cleaned to use
again.
■ Saturated carbon is harmful to the
environment, replace the filter regularly.
Every time the character G appears on the
display, the filter panel must be cleaned.
Saturation of the carbon filter is shown on the
display by the character C.
Removing the filter panel
Switch off the electricity! Remove the plug
from the socket or switch the electricity off at
the mains. Pull the filter panel down (see
fig. 4).
9
USE/FILTERS
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pelgrim lsk 900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pelgrim lsk 900 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info