333459

Pelgrim idk 825 Manual

15
Zoom out
Zoom in
Previous page
1/31
Next page
Installation
Only a qualified electrician should connect
the hob to the mains supply!
Damage caused by improper installation or
connection is not covered by the guarantee.
Safety instructions
To enable the appliance to function properly,
please ensure that:
■ That the appliance is sufficiently ventilated
(see building in dimensions).
■ That the connecting cable hangs freely and
is not caught by a drawer.
■ The worktop is at least 28 mm thick.
■ The worktop is flat.
■ If the hob is to be built in any nearer than
50mm from an adjacent wall or kitchen
cabinet, either to the back or side of the
appliance, the wall or cabinet should be
lined with a heat resistant material. Whilst
the hob itself will not generate heat a
saucepan or frying pan placed on the
appliance could possibly generate
temperatures high enough to damage some
materials.
Building-in dimensions and ventilation
The electronics in the hob need to remain cool
when in use and this is achieved by the aid of
vents on the underside of the appliance. Air is
supplied through these vents. For this it is
necessary:
■ To have an air inlet in the plinth measuring
100 cm
2
venting up behind the kitchen unit
to the appliance (see fig. 11).
FOT THE FITTER
00
490
580
510
56
560
Beluchting
100 cm
2
Fig. 9: Building-in dimensions
min. 25
100 cm
2
60
min. 100
28-40
min.100 cm
2
Fig. 10
Fig. 11: In combination with an oven. Insulate
oven from hob.
24
25
Faults
Please check the following points which may solve the problem, before calling the service
department.
FAULTS
Sympton
The appliance does not work.
The lights do not light up.
The cooking zones are not
working, the message F0
appears.
The fan switches itself on.
The appliance stops suddenly.
The message F7 appears.
The lamps continue to flash
after switching on.
Cause
No power supply.
Ambient temperature too low
(5 °C) before the hob was
plugged in.
The appliance checks itself
after the loss of power.
Ventilator is not far enough
open.
Transistors overheated.
Contact between pans/wall.
An unsuitable utensil is being
used.
Poor electrical connection.
Action
Check the electrical installation
(fuse(s), connection).
After installation, wait about ten
minutes. The messages stop
flashing and you can then use
the appliance.
The fan switches itself off.
Check ventilator openings at
front and back.
Press any control. The message
disappears. Restart at a lower
setting.
Place pans apart.
Use a suitable utensil. (See
page 17).
Check if the cable is being
caught by the drawer. If it is,
have it changed by the installer.
100 cm
2
770
510
490
750
40
56
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pelgrim idk 825 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pelgrim idk 825 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info