- 26 -
The front bar opens and closes to facilitate the entry
and exit of children when they get bigger (Fig.b).
To open it, press the two round buttons at the same
time and pull the front bar outwards.
To close it, do the opposite.
16• BACKREST: It can be set in 3 positions.
To put the backrest in the required position, put the
pin in one of the 3 eyelets in the central belt, which
can be found on the rear of the backrest (Fig.a).
COVER: Button it down on both sides and attach the
elastic loops to the clips on the sides of the front bar
(Fig.b).
17• RELEASING the Skate bassinet unit from the Skate
chassis: Put the front bar in the high position (carrying
handle position), take hold of it and pull it upwards (1),
release the Skate bassinet unit first on one side (2) and
then on the other (3), pressing on the release levers.
IMPORTANT: Only carry out this procedure with the
child in the seat if it is in Skate bassinet unit mode
and if the child weighs less than 9 kg.
SKATE SEAT
18• Before attaching it to the Skate chassis, it is necessary
to press the backrest and move from the inside to the
outside to ensure that the seat is completely open (Fig.a).
• Attach the front bar (paragraph 13).
• ATTACHING the Skate seat to the Skate chassis: To
attach the Skate seat, position its couplings in their
housing on the Skate chassis and click them into place
(Fig.b).
IMPORTANT: Do not place a child in the Skate seat
before opening the Skate chassis.
19• REVERSIBILITY: The Skate seat is reversible; it can
be attached to the Skate chassis facing the person
pushing or facing forwards.
20• INCLINING Skate seat: The Skate seat can be inclined
at 3 different angles (horizontal, inclined and vertical)
both when facing the person pushing and when facing
forwards.
To incline the Skate seat, raise the handle behind the
backrest and position it as required.
21• 5-POINT SAFETY HARNESS: To fasten the harness,
push the two waist strap buckles (with the shoulder
straps attached as shown by arrow a) into the leg
divider strap until they click into position (arrow b).
To unfasten it, push the round button in the centre of
the buckle upwards (arrow c) and pull the waist straps
outwards (arrow d).
22• To tighten the waist straps, pull from both sides in the
direction of the arrow (Fig.a); to loosen them do the
opposite. The waist straps can be tightened as far as
the safety stop (Fig.b).
23• To adjust the height of the safety straps, it is necessary
to unfasten the buttons from both sides of the Skate
fabric covering (paragraph 39 b) and lift off the fabric
covering.
Pull the buckles towards you (arrow a), then slip them
through the slots in the backrest (arrow b). Pull the
shoulder straps through the fabric covering (arrow c)
and push them through the most suitable slot (arrow
d), then position the two buckles behind the backrest
(arrow e) below the support straps (fig f).
24• COVER: Button it down on both sides (Fig.a) and attach
the elastic loops to the clips on the sides of the front
bar (Fig.b).
Attach the elastic loops under the footrest (Fig.c).
With the Skate seat, the zipper of the cover can be
opened to increase the space available for the child’s
feet (Fig.d).
25• The HEIGHT of the Skate bassinet unit and Skate seat is
ADJUSTABLE: they can be set at 3 different heights.
Simultaneously press the two side buttons on the
Skate chassis and at the same time raise or lower the
Skate bassinet unit or Skate seat until you hear them
both click into place.
Look at the arrows on the Skate chassis to check that it
is correctly in position.
The procedure is also possible with the Car Seat
attached.
26• HOOD: To fit the hood, slide the clips into the matching
slots on the Skate bassinet unit or Skate seat and
fasten the buttons on the sides – 4 for the Skate
bassinet unit and 2 for the Skate seat (Fig.a).
To release it, unbutton the hood from the sides of the
Skate bassinet unit or Skate seat, press the two buttons
under the hood attachment slots and at the same time
pull out the clips (Fig.b).
27• The hood can be set in 2 different positions: it can be
pulled forwards or backwards. The zipper makes a further
adjustment possible with the Skate bassinet unit.
It also has a viewing window.
28• RAIN CANOPY: It can be fitted on both the Skate
bassinet unit and the Skate seat. Zip it to the hood
(A), move the lower part of the rain canopy below the
Skate seat (B), pass the elastic strips with the buttons
behind the Skate bassinet unit or Skate seat couplings
(C) and attach them to the rain canopy (D).
• Thanks to the elastic strips, the rain canopy can be
opened with the zipper while still attached to the Skate
seat.
• If you wish to turn the Skate seat around, it is not
necessary to remove the rain canopy because it stays
attached to the Skate seat without interfering with the
Skate chassis.
• Do not use the rain canopy indoors. Always ensure that
the child does not get too hot.
• Do not place the rain canopy near sources of heat and
keep it away from cigarettes.
• Ensure that the rain canopy is clear of any moving
mechanisms.
• Always remove the rain canopy before folding up Skate.
• Wash with a sponge and soapy water, without using
detergents.
29• FOLDING UP: Fold away the hood if it is attached.
Lower the Skate seat to the lowest level.
It is not possible to fold up the Skate chassis with
the Skate bassinet unit attached; it is necessary to
remove it.
It is possible to fold up the Skate chassis with the Skate
seat attached; it is not necessary to remove it.
If it is attached to the Skate chassis facing the person
pushing (Fig.a), pull the safety lever outwards (1) and
at the same time recline the Skate seat while lifting the
handle behind the backrest (2) and position it in line
with the Skate chassis (3).
If the Skate seat is attached to the Skate chassis facing
forwards (Fig.b), lift the handle behind the backrest and
position the Skate seat in line with the Skate chassis.
30• FOLDING UP: To fold up the Skate chassis, turn the
lever on the right hand side of the handle upwards
and then do the same with the one on the left. Press
the central closure pedal with your foot and lower the
Skate chassis. The closure clip will automatically lock
on the right hand side of the chassis.
To make the folded up Skate chassis as compact as
possible, release the Skate seat and remove the wheels.
31• TRANSPORT: Two transport modes are possible.
It can be carried by the handle under the basket, or
pulled like a trolley by straightening the main handle
and putting the front wheels in the fixed position.
SKATE CHASSIS +
PRIMO VIAGGIO CAR SEAT
Thanks to the standard adaptors, the Peg Perego group
