564359
22
Zoom out
Zoom in
Previous page
1/44
Next page
LOW, MID AND HIGH EQ
Passive tone controls that regulate the low, mid and high frequencies, respectively.
HEADPHONE JACK
This stereo jack allows signal to ow to both sides of any stereo headset. A monaural headset
may be used, but it is not recommended.
POWER LED
Illuminates when power has been supplied to the unit.
POWER SWITCH
Press the switch to the “ON” position to apply power to the unit. The POWER LED (10) will
illuminate to indicate power has been supplied to the unit.
AC POWER CORD (REAR PANEL)
This line cord provides the AC power to the unit. Connect the line cord to a properly
grounded AC supply. Damage to the equipment may occur if improper line voltage is used.
(See voltage marking on unit.) Never remove or cut the ground pin of the line cord plug.
NOTE: FOR UK ONLY
As the colors of the wires in the mains lead of this apparatus may not correspond with the colored
markings identifying the terminals in your plug, proceed as follows: (1) The wire which is colored
green and yellow must be connected to the terminal which is marked by the letter E, or by the earth
symbol, or colored green or green and yellow. (2) The wire which is colored blue must be connected
to the terminal which is marked with the letter N, or the color black. (3) The wire which is colored
brown must be connected to the terminal which is marked with the letter L or color red.
8
9
10
11
12
12
POWER AMP SECTION
Rated Power:
25 W(rms) into 8 Ω
Power @ Clipping (Typically):
(5% THD, 1 kHz, 120 V AC line)
25 W RMS into 8 Ω
Rated Consumption:
50 W, 50/60 Hz, 120 V AC
PRE AMP SECTION
The following specs are
measured @ 2 kHz with the
controls preset as follows:
Channel Select Normal (OUT)
Low and High @ 10
Mid @ 0
Pre Gain and Post Gain @ 10
Preamp Input (Normal Channel):
Impedance: High Z, 1 M Ω
Nominal Input Level: -6 dBV
70 mV RMS
Aux Input:
Input Impedance: 100 k Ω
Nominal Input Level: .5V RMS,
-6 dBV
(Stereo jack designed for use
with stereo headphone output on
CD/Tape Player)
Headphone Output:
Load Impedance: 8 Ω
Nominal Power Output:
50 mW into 8 Ω
(Stereo jack, monaural signal
disconnects internal speaker
when phone plug is inserted.)
Equalization:
Special low, mid, and high
passive type EQ
Dimensions (H x W x D):
14.75" x 16.25" x 8.5"
37.47 cm x 41.27 cm x 34.80 cm
Weight:
17.8 lbs.
8.07 kg
Specifications
Specications subject to change without notice.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Peavy Rage 258 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Peavy Rage 258 in the language / languages: English as an attachment in your email.

The manual is 8,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info