564342
27
Zoom out
Zoom in
Previous page
1/44
Next page
27

Input connections are made via the 3-pin XLR (pin 2+) or 6.3 mm plug combination connectors on the rear panel of the
amplifier. The inputs are actively balanced. The input overload point is high enough to accept the maximum output level of
virtually any signal source.

This XLR jack supplies parallel output signals from the associated channel for patching to this amplifier and/or additional
power amplifier inputs. The Thru/Out jack is affected by the position of the associated Channel Mode switch. This XLR jack
also provides an unbalanced (tip/sleeve) output to be patched with single-conductor shielded cables.

All models have one combination 4 pole twist lock output connector per channel. Channel A ouput allows for CH A 1+ Pos / 1-
Neg and channel B 2+ Pos / 2- Neg to use a single 4 conductor speaker cable.

In the unlikely event of operating conditions that may potentially damage the amplifier, the circuit breaker may trip. After
inspecting the cables and connections, the amplifier can be reset. If the circuit breaker trips a second time, contact the local
Peavey authorized service center.

This is the receptacle for an IEC line cord, which provides AC power to the unit. Connect the line cord to this connector to
provide power to the unit. Damage to the equipment may result if improper line voltage is used. (See line voltage marking on
unit).
Never break off the ground pin on any equipment. It is provided for your safety. If the outlet used does not have a ground pin, a
suitable grounding adapter should be used and the third wire should be grounded properly. To prevent the risk of shock or fire
hazard, always make sure that the amplifier and all associated equipment is properly grounded.

As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying the
terminals in your plug, proceed as follows: (1) The wire which is colored green and yellow must be connected to the terminal
which is marked by the letter E, or by the Earth symbol, or colored green or green and yellow. (2) The wire which is colored
blue must be connected to the terminal which is marked with the letter N, or the color black. (3) The wire which is colored
brown must be connected to the terminal which is marked with the letter L, or the color red.
Rear Panel
IPR2

IPR2

13
13
14
14
12
12
12
12
10
11
12
13
14
11
11
11
11
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Peavy IPR2 5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Peavy IPR2 5000 in the language / languages: English as an attachment in your email.

The manual is 22,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info