564365

Peavey Tour Series TKO Combo Manual

26
Zoom out
Zoom in
Previous page
1/144
Next page
TKO
®
Rear Panel
16
17
18
19
14
15
POWER SWITCH
To apply power to the unit, ip the switch to the “On” position. The green LED will illuminate, indicating power is
being supplied.
CAUTION: The on/off switch in this unit does not break both sides of the primary mains.
Hazardous energy can be present inside the chassis even when the on/off switch is in the
OFF position.
AC POWER INLET:
This is the receptacle for an IEC line cord, which provides AC power to the unit. Connect the line cord to this
connector to provide power to the unit. Damage to the equipment may result if improper line voltage is used. (See
line voltage marking on unit).
Never break off the ground pin on any equipment. It is provided for your safety. If the outlet used does not have
a ground pin, a suitable grounding adapter should be used, and the third wire should be grounded properly.
To prevent the risk of shock or re hazard, always make sure that the amplier and all associated equipment is
properly grounded.
NOTE: FOR UK ONLY
As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings
identifying the terminals in your plug, proceed as follows: (1) The wire that is colored green and yellow must be
connected to the terminal that is marked by the letter E, or by the Earth symbol, or colored green or green and
yellow. (2) The wire that is colored blue must be connected to the terminal that is marked with the letter N, or the
color black. (3) The wire that is colored brown must be connected to the terminal that is marked with the letter L,
or the color red.
EXTERNAL SPEAKER OUTPUT
1/4" powered output for powering a passive enclosure.
EFFECTS LOOP
The Send Jack provides a pre amp output that may be used to drive slave ampliers and external effects
processors. The Return Jack provides a power amp input for the last effect in the chain.
NOTE: When using the unit as a slave power amplier, the Return Jack should be used as the input.
GROUND LIFT
This button is provided to prevent a ground loop that may result in "hum" noise. When depressed (IN position),
Ground Lift is engaged.
DIRECT INTERFACE (DI)
This is a built-in, balanced Direct Interface used to send a buffered, unprocessed signal to an external mixer.
NOTE: The Direct Interface features failsafe circuitry, which runs on standard 48-volt phantom power from
the mixer. This allows the DI to continue functioning even in the event of a blown circuit breaker or amplier
shutdown. In the event of a failsafe operation, the mute switch will be bypassed. This circuit is active, even when
the power switch is in the "Off" position.
16
17
18
19
15
14
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Peavey Tour Series TKO Combo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Peavey Tour Series TKO Combo in the language / languages: English as an attachment in your email.

The manual is 8,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info