564365
23
Zoom out
Zoom in
Previous page
1/144
Next page
17
18
AC POWER INLET:
This is the receptacle for an IEC line cord, which provides AC power to the unit. Connect the line cord to this
connector to provide power to the unit. Damage to the equipment may result if improper line voltage is used.
(See line voltage marking on unit).
Never break off the ground pin on any equipment. It is provided for your safety. If the outlet used does not
have a ground pin, a suitable grounding adapter should be used, and the third wire should be grounded
properly. To prevent the risk of shock or re hazard, always make sure that the amplier and all associated
equipment is properly grounded.
NOTE: FOR UK ONLY
As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings
identifying the terminals in your plug, proceed as follows: (1) The wire that is colored green and yellow must
be connected to the terminal that is marked by the letter E, or by the Earth symbol, or colored green or green
and yellow. (2) The wire that is colored blue must be connected to the terminal that is marked with the letter
N, or the color black. (3) The wire that is colored brown must be connected to the terminal that is marked
with the letter L, or the color red.
TWEETER SWITCH
This switch turns the tweeter on/off. Usually when the CRUNCH effect is engaged, this switch would be
switched to the OFF position.
EXTERNAL SPEAKER OUTPUT
"Combi" type powered output for powering a passive enclosure.
FOOTSWITCH JACK
Plug your TNT footswitch into this 1/4" jack. The footswitch controls the crunch effect and the compressor
on/off.
NOTE: The crunch and compressor buttons MUST be pushed in to operate with the footswitch.
EFFECTS LOOP
The Send Jack provides a pre amp output that may be used to drive slave ampliers and external effects
processors. The Return Jack provides a power amp input for the last effect in the chain.
NOTE: When using the unit as a slave power amplier, the Return Jack should be used as the input.
GROUND LIFT
This button is provided to prevent a ground loop that may result in "hum" noise. When depressed (IN
position), Ground Lift is engaged.
DIRECT INTERFACE (DI)
This is a built-in, balanced Direct Interface used to send a buffered, unprocessed signal to an external mixer.
PEAVEY LOGO BACKLIGHT SWITCH
This button turns the backlight on the Peavey Logo on or off.
19
20
21
22
23
24
25
TNT Rear Panel
20
22
23
24
25
19 21
18
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Peavey Tour Series TKO Combo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Peavey Tour Series TKO Combo in the language / languages: English as an attachment in your email.

The manual is 8,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info