Manual Partner Colibri II plus (page 6 of 71) (English, German, Dutch, French, Italian, Spanish)

518738

Zoom out

Zoom in

1/71

NOTE: I f engine has not started, pull starter

rope 5 more pulls. If enginestill does not run, it

is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing

the choke lever in the RUN position; then, pull

the rope to clear the engine of excess fuel.

This could require pulling the starter handle

many times depending on how badly the unit

is f looded. If t h e unit s till doesn’t start, refer to

TROUBLESHOOTING TABLE.

OPERATING INSTRUCTIONS

OPERA TING POSITION

Cut from your right to your left.

SWE

Eye protection

Long pants

Heavy shoes

Hearing

protection

WARNING: Always wear eye p rotec-

tion and hearing protection. Never lean over

the trimmer head. Rocks or debris can rico-

chet or be thrown into eyes and face and

cause blindness o r other serious injury.

Do not run the engine at a higher speed than

necessary . The cutting line will cut ef ficientl y

when the engine i s run at less th an full throttle.

At lower speeds, there is less engine noise and

vibration. The cutting line w ill last longer and will

be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the

engine to return to idle speed when not cutting.

To stop engine:

S Release the throttle trigger.

S Move the ON/OFF switch to t he OFF posi-

tion.

TRIMMER LINE ADVANCE

Advance line by tapping the bottom of the cut-

ting head light ly on the ground while engineis

running at full speed. The metal line limiter

blade attached t o the guard will cut the line to

the proper length.

WARNING: Use only 2 mm diameter

line. Other sizes and shapes of line will not ad-

vance properly and will result in improper cut-

ting head functionor cancause serious injury.

Do not use other ma terials such as wire,

string, rope, etc. Wire can break off during

cutting and become a dangerous missile that

can cause serious injury .

CUTTING METHODS

WARNING: Use minimum speed and

do not crowd the line when cutting around

hard objects (rock, gravel, fence posts, etc.),

which candamage the trimmer head, become

entangled in the line, or be thrown causing a

serious hazard.

S The tip of the line does the cutting. You will

achieve the best performance and mini-

mum line wear by not crowding the line into

the cutting area. The right and wrong ways

are shown below.

Tip of the Line

Does The Cutting

Right Wrong

Line Crowded Into

Work Area

S The line will easily remove grass and

weeds from around walls, fences, trees and

flower beds, but it also can cut t he tender

bark of trees or shrubs and scar fences.

S For trimming or scalping, use less than full

throttle to increase line life and decrease

head wear, especially:

S During light duty cutting.

S Near objects around which the line can-

wrap such as small posts, trees or fence

wire.

S For mowing or sweeping, use full throttle for

a good clean job.

TRIMMING -- Hold the bottom of the trimmer

head about 80 m m above the ground and at an

angle. Allow only the ti p of the line to make con-

tact. Do not force trimmer line into work area.

Trimming

3 in. (8 cm)

Above Ground

SCALPING -- The scalping technique removes

unwanted vegetation. Hold the bottom of the

trimmer head about 80 mm above the ground

and at a n ang le. Allow the t ip o f the lin e to strike

the ground around trees, posts, monuments,

etc. Th is technique increases li ne wear.

Scalping

MOWING -- Your trimmer is idea l for mowing

in places conventional lawn m owers cannot

reach. In the m owing position, keep t he line

parallel to the ground. Avoid pressing the

head into the ground as this can scalp the

ground and damage the tool.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Partner Colibri II plus in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Partner Colibri II plus Manual

Product: