Manual Parkside PZKS 2000 B2 - IAN 338493 (page 11 of 100) (English, German, Dutch, Danish, French)

779323

Zoom out

Zoom in

1/100

6GB/IE/NI

g) Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with

the outside bowed face toward the fence. Al-

ways make certain that there is no gap be-

tween the workpiece, fence and table along

the line of the cut. Bent or warped workpieces can

twist or shift and may cause binding on the spinning saw

blade while cutting. There should be no nails or foreign

objects in the workpiece.

h) Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the work-

piece. Small debris or loose pieces of wood or other

objects that contact the revolving blade can be thrown

with high speed.

i) Cut only one workpiece at a time. Stacked multi-

ple workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

j) Ensure the mitre saw is mounted or placed on

a level, ﬁrm work surface before use. A level and

ﬁrm work surface reduces the risk of the mitre saw becom-

ing unstable.

k) Plan your work. Every time you change the bev-

el or mitre angle setting, make sure the adjust-

able fence is set correctly to support the work-

piece and will not interfere with the blade or

the guarding system. Without turning the tool “ON”

and with no workpiece on the table, move the saw blade

through a complete simulated cut to assure there will be no

interference or danger of cutting the fence.

l) Provide adequate support such as table exten-

sions, saw horses, etc. for a workpiece that is

wider or longer than the table top. Workpieces

longer or wider than the mitre saw table can tip if not

securely supported. If the cut-oﬀ piece or workpiece tips,

it can lift the lower guard or be thrown by the spinning

blade.

m) Do not use another person as a substitute for

a table extension or as additional support. Un-

stable support for the workpiece can cause the blade to

bind or the workpiece to shift during the cutting operation

pulling you and the helper into the spinning blade.

n) The cut-oﬀ piece must not be jammed or

pressed by any means against the spinning

saw blade. If conﬁned, i.e. using length stops, the cut-

oﬀ piece could get wedged against the blade and thrown

violently.

o) Always use a clamp or a ﬁxture designed to

properly support round material such as rods

or tubing. Rods have a tendency to roll while being cut,

causing the blade to “bite” and pull the work with your

hand into the blade.

p) Let the blade reach full speed before contact-

ing the workpiece. This will reduce the risk of the

workpiece being thrown.

q) If the workpiece or blade becomes jammed,

turn the mitre saw oﬀ. Wait for all moving

parts to stop and disconnect the plug from

the power source and/or remove the battery

pack. Then work to free the jammed material.

Continued sawing with a jammed workpiece could cause

loss of control or damage to the mitre saw.

r) After ﬁnishing the cut, release the switch, hold

the saw head down and wait for the blade to

stop before removing the cut-oﬀ piece. Reaching

with your hand near the coasting blade is dangerous.

s) Hold the handle ﬁrmly when making an incom-

plete cut or when releasing the switch before

the saw head is completely in the down posi-

tion. The braking action of the saw may cause the saw

head to be suddenly pulled downward, causing a risk of

injury.

Safety Instructions for the handling of saw blades

1. Do not use damaged or deformed saw blades.

2. Do not use any insertion tools with cracks. Sort out cracked

insertion tools. Repairs are not permitted.

3. Do not use saw blades made of high speed steel.

4. Check the condition of the saw blades before using the

crosscut, drag and mitre saw.

5. Make sure that a suitable saw blade for the material to

be cut is selected.

6. Only use saw blades recommended by the manufacturer.

Saw blades designed to cut wood and similar materials

must comply with EN 847-1.

7. Do not use saw blades made of high-speed alloy steel

(HSS steel).

8. Only use saw blades for which the maximum permissible

speed is not lower than the maximum spindle speed of the

crosscut, drag and mitre saw and which are suitable for

the material to be cut.

9. Observe the saw blade direction of rotation.

10. Only insertion the saw blade if you have mastered their

use.

11. Observe the maximum speed. The maximum speed speci-

ﬁed on the insertion tool may not be exceeded. If speci-

ﬁed, observe the speed range.

12. Clean grease, oil and water oﬀ of the clamping surfaces.

13. Do not use any loose reducing rings or bushes for the re-

ducing of holes on saw blades.

14. Make sure that ﬁxed reducer rings for securing the inser-

tion tool have the same diameter and have at least 1/3 of

the cutting diameter.

15. Make sure that ﬁxed reducer rings are parallel to each

other.

16. Handle insertion tool with caution. They are ideally stored

in the originally package or special containers. Wear

protective gloves in order to improve grip and to further

reduce the risk of injury.

17. Prior to the use of insertion tools, make sure that all protec-

tive devices are properly fastened.

18. Prior to use, make sure that the insertion tool meets the

technical requirements of this electric tool and is properly

fastened.

19. Only use the supplied saw blade for cutting wood, never

for the processing of metals.

20. Only use saw blade diameters in accordance with the

markings on the saw.

21. Use additional workpiece supports, if required for work-

piece stability.

22. Workpiece support extensions must always be secured

and used during work.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PZKS 2000 B2 - IAN 338493 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 4.9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PZKS 2000 B2 - IAN 338493 Manual

Product: