558707
7
Zoom out
Zoom in
Previous page
1/13
Next page
9 GB/IE/CY
J Check the condition of the mains lead on your
electrical power tool regularly and have any
damage repaired by a competent specialist.
J Check the condition of extension leads regu-
larly and replace them if they are damaged.
J Keep handles and hand grips clean, dry and
free of oil and grease.
15. Pull the mains plug out of the mains
socket.
J Do this if the electrical power tool is not being
used, before carrying out maintenance tasks
on the electrical power tool and whenever you
are changing inserted tools, e.g. saw blades,
drills or router bits.
16. Make sure that no spanners, keys
etc. are left attached.
J Check before switching on that all spanners,
keys and setting tools have been removed.
17. Avoid unintentionally starting up
the device.
J Check that the switch is set to OFF on the de-
vice when the mains plug is inserted into the
mains socket.
18. Using an extension lead for working
outdoors.
J When working outside, always use an approved
and appropriately labelled extension lead.
19. Remain alert.
J Watch what you are doing. Proceed with cau-
tion. Do not use electrical power tools if you
cannot concentrate.
20. Check the electrical power tool for
damage.
J Before the electrical power tool is used, care-
fully check the safety equipment and any
slightly damaged parts to see that they are still
working properly.
J Check that all moving parts on the tool are
working properly, can move freely and are not
damaged. All parts must be correctly attached
and fulfil all the requirements necessary to allow
the electrical power tool to operate properly.
J Damaged safety equipment and components
must be properly repaired or replaced at a
competent electrical equipment repair centre
unless otherwise indicated in the operating in-
structions.
J Damaged switches must be replaced at a
Customer Service Centre.
J Never use an electrical power tool that cannot
be switched on and off properly.
21. CAUTION!
J The use of inserted tools and accessories other
than those recommended by the manufacturer
could lead to you being injured.
22. Have your electrical power tool
repaired at an electrical equipment
repair specialist.
J This electrical power tool complies with the
relevant safety regulations. Repairs may only
be carried out by a specialist electrical repair
centre using original spare parts, otherwise
injury could occur to the user.
Safety advice relating
specifically to this device
Safety precautions:
J Do not use blunt, cracked, distorted
or damaged saw blades. Saw blades
with blunt or misaligned teeth are in effect too
wide for the designed saw gap and this gives
rise to increased friction, jamming and kickback.
J Always use a saw blade of the correct
size and with the appropriate central
fixing hole bore (e.g. star-shaped or
round). Saw blades that do not correspond
with the attachment components on the saw will
not run true and could lead to loss of control.
J Replace table inserts when worn out.
J Never operate the electrical power
tool without the table insert. Replace a
table insert if it has defects.
J Always use recommended saw
blades complying with EN 847-1.
Note: When changing to a different saw
blade make sure that the cutting width is greater
and the stock thickness smaller than the thick-
ness of the riving knife.
J Make sure that you use a saw blade suitable
for the material you are cutting.
J If necessary wear suitable personal protective
clothing.
Safety advice
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PTKS 1800 - KH 3160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTKS 1800 - KH 3160 in the language / languages: English as an attachment in your email.

The manual is 1,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PTKS 1800 - KH 3160

Parkside PTKS 1800 - KH 3160 User Manual - German, Dutch, French - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info