706370
129
Zoom out
Zoom in
Previous page
1/204
Next page
129
ES
Trabajar con el tope
paralelo
Ajustar la
altura del tope
(Imagen 24-26)
- El riel de tope (39) del tope paralelo

diferente altura.
- Según el grosor del material a cortar,
el riel tope (39) ha de utilizarse de
diferente manera. Para materiales

inferior a 25 mm) utilizar Imagen 24.
Para materiales gruesos (espesor de
la pieza de labor superior a 25 mm)
utilizar Imagen 26.
Girar el riel de tope
(Imagen 24-26)
 
primero las dos tuercas de mariposa
(h).
- Ahora, el riel de tope (39) se puede
retirar del carril guía (14) y con el
carril correspondiente volver a introdu-
cirlo por encima.
- Vuelva a apretar las tuercas de mari-
posa (h).
Ajustar el ancho de corte
(Imagen 27-28)
- Al cortar piezas de madera en longitu-
dinal ha de utilizarse el tope paralelo
(14).
- El tope paralelo debería montarse en
el lado derecho de la hoja de sierra
(5).
- Introducir el tope paralelo lateralmente
en el carril guía (13) (Imagen 28).
Ajustar la profundidad de
corte
(Imagen 23)
Al girar la rueda de mano (12) para ajus-
tar la altura, puede regular la profundidad
de corte (de continuo) de la hoja de sierra.
Importante: la rueda de mano (12)
ha de estar sacada hacia afuera
para ajustar la profundidad de
corte, si está en posición comprimi-
da lo que se ajusta es el ángulo de
corte.
- En sentido contrario a las agujas del
reloj: mayor profundidad de corte
- En sentido de las agujas del reloj:
menor profundidad de corte
Haciendo un corte de prueba puede
comprobar el ajuste.
Ajuste del ángulo
(Imagen 23)
Con la sierra circular de mesa se pueden
realizar cortes diagonales hacia la
izquierda de 0°-45° con respecto al
riel de tope.
Antes de realizar cualquier corte compru-
ebe que entre el riel de tope (39),
la posicionadora de corte diagonal
(Imagen 1, nº 8) y la hoja de sierra
(5) no se puede producir ninguna
colisión.
- Soltar mango para inmovilizar (9)
- Al introducir y girar la rueda de
mano (12) se ajusta la medida del
ángulo que se desea según una
escala.
- Enclavar el mango (9) para inmovili-
zar en el ángulo que se desea.
129


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-ptk-2000-b2---ian-273460

Reset search

  • need new motor have it for four years has not done five days work because i have bigger saw the commutator has split
    Submitted on 12-11-2021 at 15:05

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PTK 2000 B2 - IAN 273460 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTK 2000 B2 - IAN 273460 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info