595333

Parkside PTK 2000 A1 - IAN 104416 Manual

20
Zoom out
Zoom in
Previous page
1/64
Next page
15GB
ment and its accessories are made of various types of
material, such as metal and plastic. Defective compo-
nents must be disposed of as special waste. Ask your
dealer or your local council.
17. Warranty certicate
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your
device develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you
would prefer to call us then we are also happy to offer our assistance under the service number printed below. Please note the
following terms under which guarantee claims can be made:
• These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge
you for this guarantee.
• Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectication of
these defects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade
or industrial applications. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial
applications or for other equivalent activities. The following are also excluded from our guarantee: compensation for transport
damage, damage caused by failure to comply with the installation/assembly instructions or damage caused by unprofessional
installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type), mis-
use or inappropriate use (such as overloading of the device or use of non-approved tools or accessories), failure to comply with
the maintenance and safety regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of force or
external inuences (e.g. damage caused by the device being dropped) and normal wear resulting from proper operation of the
device.
The guarantee is rendered null and void if any attempt is made to tamper with the device.
• The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee claims should be
submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be
accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs
are carried out or parts are replaced. In such cases, the work performed or parts tted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work performed or parts tted. This also applies when an
on-site service is used.
• In order to assert your guarantee claim, please send your defective device postage-free to the address shown below. Please
enclose either the original or a copy of your sales receipt or another dated proof of purchase. Please keep your sales receipt in
a safe place, as it is your proof of purchase. It would help us if you could describe the nature of the problem in as much detail
as possible. If the defect is covered by our guarantee then your device will either be repaired immediately and returned to you,
or we will send you a new device.
Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope of this guar-
antee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.
16. Troubleshooting
Problem Possible Cause Help
Saw blade gets loose
after turning off the
motor
Fastening nut tightened insufciently Tighten fastening nut, M20 left-handed thread
Motor does not start a) Fastening nut tightened insufciently
b) Extension cable defect
c) Connections on the motor or switch defect
a) Check the mains fuse.
b) See “Electrical Connection” in the operating
manual
c) Have it checked by an electrician
No motor output turns
off automatically
Overload by dull saw blade, thermoprotection
is triggered
Insert a sharpened saw blade; motor can be turned
on again after the cooling period
Burns on the cutting
surface
c) with longitudinal cuts
d) with cross cuts
a) Fastening nut tightened insufciently
b) Wrong saw blade
c) Longitudinal stop not parallel
d) Slide carriage not parallel
a) Insert a sharpened saw blade
b) Insert saw blade with 20 or 28 teeth for
longitudinal cuts
c) Exchange the longitudinal stop
Align the slide carriage with the saw blade
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PTK 2000 A1 - IAN 104416 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTK 2000 A1 - IAN 104416 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info