Manual Parkside PTBM 710 A1 - IAN 314564 (page 22 of 88) (English, German, Dutch, French, Polish)

706362

Zoom out

Zoom in

1/88

17GB/IE

d) Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool.

Power tools are dangerous in the hands of untrained us-

ers.

e) Maintain power tools and accessories.

Check for misalignment or binding of moving parts, break-

age of parts and any other condition that may aﬀect the

power tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by poor-

ly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed.

Use of the power tool for operations diﬀerent from those

intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery han-

dles and grasping surfaces do not allow for safe handling

and control of the tool in unexpected situations.

Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

is maintained.

Drill safety warnings

a) The drill must be secured. A drill that is not properly

secured may move or tip over and may result in personal

injury.

b) The workpiece must be clamped or secured to

the workpiece support. Do not drill pieces that

are too small to be clamped securely. Holding

the workpiece by hand during operation may result in

personal injury..

c) Do not wear gloves. Gloves may be entangled by

the rotating parts or chips leading to personal injury.

d) Keep your hands out of the drilling area while

the tool is running. Contact with rotating parts or

chips may result in personal injury.

e) Make sure the accessory is rotating before

feeding into the workpiece. Otherwise the acces-

sory may become jammed in the workpiece causing un-

expected movement of the workpiece and personal injury.

f) When the accessory is jammed, stop applying

downward pressure and switch oﬀ the tool.

Investigate and take corrective actions to elim-

inate the cause of the jam. Jamming can cause un-

expected movement of the workpiece and personal injury.

g) Avoid generating long chips by regularly in-

terrupting downward pressure. Sharp metal

chips may cause entanglement and personal injuries.

h) Never remove chips from the drilling area

while the tool is running. To remove chips,

move the accessory away from the workpiece,

switch oﬀ the tool and wait for the accessory

to stop moving. Use tools such as a brush or

hook to remove chips. Contact with rotating parts or

chips may result in personal injury.

i) Accessories with speed ratings must be rated

at least equal to the maximum speed marked

on the power tool. Accessories running faster than

their rated speed can break and ﬂy apart.

Attention: Laser radiation

Do not stare into the beam

Class 2 laser

Protect yourself and you environment from acci-

dents using suitable precautionary measures

• Do not look directly into the laser beam with unprotected

eyes.

• Never look into the path of the beam.

• Never point the laser beam towards reﬂecting surfaces and

persons or animals. Even a laser beam with a low output

can cause damage to the eyes.

• Caution - methods other than those speciﬁed here can result

in dangerous radiation exposure.

• Never open the laser module. Unexpected exposure to the

beam can occur.

• The laser may not be replaced with a diﬀerent type of laser.

• Repairs of the laser may only be carried out by the laser

manufacturer or an authorised representative.

• Labelling and placement of warning stickers, see ﬁg. 8 and 9.

Warning! This electric tool generates an electromagnetic ﬁeld

during operation. This ﬁeld can impair active or passive medi-

cal implants under certain conditions. In order to prevent the

risk of serious or deadly injuries, we recommend that persons

with medical implants consult with their physician and the man-

ufacturer of the medical implant prior to operating the electric

tool.

Remaining hazards

Even if you use this electric power tool in accord-

ance with instructions, certain residual risks can-

not be eliminated. Remaining hazards can be

minimized by following the instructions in „Safety

instructions“, „Intended Use“ and in the entire op-

erating manual. The following hazards may arise

in connection with the equipment’s construction

and layout:

• Lung damage if suitable dust protection mask is not worn.

• Hearing damage if suitable hearing protection is not worn.

• Damage to health resulting from hand/arm vibration if the

device is used over an extended period of time or if it is not

properly operated and maintained.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTBM 710 A1 - IAN 314564 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 4,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PTBM 710 A1 - IAN 314564 Manual

Product: