679120

Parkside PSTD 800 B2 - IAN 283022 Manual

11
Zoom out
Zoom in
Previous page
1/37
Next page
PSTD 800 B2
GB
│
IE
│
NI
│
CY 
│
 7 ■
Operation
Setting the cutting angle
♦ Undo the clamping screws with the hex
key and pull the footplate to the rear.
♦ Adjust the cutting angle to 0°/15°/30°/45°
with the aid of the markings on the footplate
.
Push the footplate to the front so that the
locking pin engages in the toothing .
♦ Retighten the clamping screws
with the Hex
key .
NOTE
► When using a cutting angle of 15°/30°/45°,
the pivoting blade guard
and splinter guard
must be detached beforehand!
Setting the stroke rate
♦ Use the stroke rate adjusting wheel to set the
required stroke rate.
Adjusting the pendulum stroke
♦ You can use the pendulum stroke switch to
adjust the pendular movement of the saw blade
. You can achieve fine, clean-cut edges with-
out pendular movement (setting "0"). Deactivate
pendular movement when working on thin
workpieces. You can achieve an increasingly
fast work rate if the pendulum stroke is activated
(settings 1–3).
Switching ON/OFF
Switching the appliance on:
Press the ON/OFF switch
.
Switching the appliance off:
Release the ON/OFF switch
.
Switching to continuous operation:
Press the ON/OFF switch
and lock it in this
position with the ON/OFF switch lock button .
Switching off continuous operation:
Press the ON/OFF switch
and release it again.
Switching the laser/working light
ON/OFF
ON/OFF switch:
Press the ON/OFF switch
for the until the
required function is active.
LASER and WORKING LIGHT → WORKING
LIGHT → LASER → SWITCH OFF
Sawdust blowing function
Switching the sawdust blowing function on:
♦ Slide the sawdust blower function switch
in
the position .
Supporting the extraction function:
♦ Slide the sawdust blower function switch
in
the position “0”.
Maintenance and cleaning
WARNING! RISK OF INJURY! Switch
the appliance off and remove the
power plug before starting any work on the
appliance.
■ The appliance must always be kept clean, dry
and free from oil or grease.
■ Use a soft, dry cloth to clean the housing.
WARNING!
■ If the supply cord of this power tool is dam-
aged, it must be replaced by a specially
prepared cord available through the service
organization.
■ Replace the saw blade
as soon as its teeth
are too blunt for adequate sawing.
■ Clean the appliance after completing your
sawing work.
■ Remove any dirt (e.g. sawdust). If necessary,
clean the saw blade mount with a brush or
compressed air.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PSTD 800 B2 - IAN 283022 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PSTD 800 B2 - IAN 283022 in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PSTD 800 B2 - IAN 283022

Parkside PSTD 800 B2 - IAN 283022 User Manual - German, Dutch, Danish, French - 47 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info