779475
28
Zoom out
Zoom in
Previous page
1/115
Next page
PSBSAP 20-Li A1
24 GBIE
Inserting/removing the battery pack
Inserting the battery pack
Set the rotation direction switch to the middle
position (lock). Push the battery pack! into
the handle until it clicks into place.
Removing the battery pack
Press the release button. and remove the
battery pack!.
Checking the battery charge level
Press the battery charge level button1 to
check the status of the battery (see the main
diagram). The status/remaining charge will be
shown on the battery display LED6 as follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Additional handle
NOTE
For safety reasons, you should never use
this tool without the additional handle
attached.
Loosen the strap on the additional handle
by turning it clockwise.
Slide the mounting ring for the additional
handle over the chuck3.
Turn the additional handle to the required
position.
Afterwards, twist the additional handle
anticlockwise again to tighten it.
Depth stop
Push the locking button for the depth stop
and keep it pushed in.
Fit the depth stop into the additional
handle.
Make sure that the teeth on the depth stop
point upwards and downwards.
Pull the depth stop out until the distance
between the tip of the drill and the tip of the
depth stop corresponds with the required
drilling depth.
Release the locking button for the depth stop
to lock the depth stop in place.
Changing tools
Your cordless impact drill driver has a fully auto-
matic spindle lock .
When the motor is stopped, the power train is
locked so that the chuck3 can be opened by
turning . After you have attached the desired
tool and tightened it by turning the chuck , you
can continue working. The spindle lock is released
automatically when the motor is started (by pressing
the ON/OFF switch).
Torque selection/selecting the
operating mode
You can set the torque using the torque selection
ring- or by choosing between the drill setting
and the hammer drill setting .
Select a low level for small screws or soft
materials.
Select a high level for large screws, hard
materials or removing screws.
Select the drill setting for drilling work by adjusting
the torque selection ring to the position .
Select the hammer drill setting for hammer drilling
work by adjusting the torque selection ring to
the position .
IB_329699_PSBSAP20-LiA1_LB8.indb 24 26.08.20 13:41
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PSBSAP 20-Li A1 - IAN 329699 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PSBSAP 20-Li A1 - IAN 329699 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 1.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info