679123
22
Zoom out
Zoom in
Previous page
1/55
Next page
21 IT/MT
Messa in esercizio / Esercizio dell‘apparecchio
Montaggio della protezione
da trucioli staccati
Estrarre il pattino
10
dalla piastra di base
9
.
Inserire la protezione da trucioli staccati
16
da
sotto la piastra di base
9
e spingerla nelle
cave previste per essa. La protezione da trucio-
li può impedire il distacco della superficie.
Montaggio del finecorsa parallelo
Il finecorsa parallelo
19
può essere fissato a scelta
sulla destra oppure la sinistra dell’apparecchio
(vedi Fig. A).
Allentare le due viti dell’apertura di
inserimento
15
.
Spingere il finecorsa parallelo
15
nell’apertura
di inserimento
19
e determinare la distanza.
Serrare nuovamente le due viti alettate.
Collegare l’aspirazione trucioli
Inserire il manicotto di aspirazione
7
nel
canale di aspirazione
8
fino a quando si
sente che il manicotto si è incastrato.
Collegare il dispositivo omologato per l’aspira-
zione di polveri e trucioli al manicotto per
l’aspirazione
7
(vedi Fig. C).
Esercizio dell‘apparecchio
Regolare l’angolo di taglio
Allentare la vite di fissaggio
11
con la chiave
ad esagono incassato
20
.
Regolare l’angolo di taglio sulla piastra di
base
9
mediante le marcature punzonate
0° / 15° / 30° / 45° (sinistra / destra). A questi
valori corrispondono le cavità per la regolazio-
ne dell’angolo del taglio. L’alloggiamento
possiede una spina d arretramento
21
o (vedi
Fig. B), la quale deve innestarsi nella cavità
corrispondente.
Serrare la vite di fissaggio
11
con la chiave
ad esagono incassato
20
.
Regolazione del numero di colpi
Portare la rotella selezione del numero di giri
4
sul numero di colpi desiderato.
Rilevare la regolazione ottimale sempre prima,
eseguendo una prova pratica.
Regolazione del sollevamento
oscillante
E’ possibile regolare il movimento oscillante della
lama
12
operando sull’interruttore del sollevamento
oscillante
14
. Senza il sollevamento oscillante
(Posizione “0”) si ottengono angoli di taglio molto
fini e puliti. Se si lavorano pezzi fini, spegnere il
sollevamento oscillante.
Con sollevamento oscillante attivato (Posizione
1 3) si ottiene un procedimento di lavoro sempre
più veloce.
Rilevare la regolazione ottimale sempre prima,
eseguendo una prova pratica.
Accensione / Spegnimento
PERICOLO! Prima di collegare l’apparecchio
alla corrente controllare che questa corrisponde a
230 V
~
50 Hz e che vi sia un fusibile 16 A
presente!
22


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-pphss-730-se---kh-3021

Reset search

  • Hoe kom ik aan de 2 koolborstel houdertjes waar de koolborstels in zitten. Van beide houdertjes zijn de pennen waar de drukveer aan hoort te zitten afgebroken. Ook de beide drukveertjes voor de koolborstels zijn weg. Submitted on 16-11-2021 at 16:00

    Reply Report abuse
  • Is it possible to bye the speedcontrol as a part? It didn't start. Can rotate some when I give the fanwheel o puch.
    OR, howe to disconect the whole speedcontrol. Howe to conect the wires? Submitted on 9-6-2021 at 10:07

    Reply Report abuse
  • parkside pphss 730 se kh 3021 I didn't start the switch is ok Submitted on 18-6-2020 at 15:41

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PPHSS 730 SE - KH 3021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PPHSS 730 SE - KH 3021 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PPHSS 730 SE - KH 3021

Parkside PPHSS 730 SE - KH 3021 User Manual - German, Dutch, French, Italian - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info