679123
12
Zoom out
Zoom in
Previous page
1/55
Next page
11 ES
Puesta en funcionamiento / Manejo
¡ADVERTENCIA!
Antes de proceder a los
trabajos en la máquina, desenchufe siempre el
equipo de la toma de corriente. Si no lo hace
corre el riesgo de sufrir lesiones.
Gire el mandril de sujeción rápida
18
y
manténgalo girado.
Presione la hoja de sierra
14
que necesita has-
ta el tope del mandril de sujeción rápida
18
.
La hoja de sierra
14
se engatilla.
La hoja de sierra
14
debe alojarse enel rodillo
guía
13
.
Suelte el mandril de sujeción rápida
18
;
debe volver a la posición inicial.
La hoja de sierra
14
está bloqueada.
Montar la protección
contra astillado
Extraiga la zapata deslizante
10
de la placa
base
9
.
Introduzca la protección contra astillado
16
de abajo en la placa base
9
y deslícela en
la ranura prevista. La protección contra astilla-
do puede evitar un desgarre en la superficie.
Montar el tope paralelo
Puede seleccionar la fijación del tope paralelo
19
a la derecha o a la izquierda del aparato
(véase fig. A).
Afloje los dos tornillos de las aberturas para
deslizamiento
15
.
Deslice el tope paralelo
19
en las aberturas
para deslizamiento
15
.
Apriete los dos tornillos de fijación.
Acoplar el aspirador de virutas
Introduzca el manguito de aspiración
7
en
el canal de aspiración
8
hasta que esté
claramente engatillado.
Acople un aspirador de virutas y polvo autori-
zado al manguito de aspiración
7
(véase fig. C).
Manejo
Ajustar ángulo de corte
Desatornille los tornillos de sujeción
11
con la
llave macho hexagonal
20
.
Ajuste el ángulo de corte 0° / 15° / 30° / 45°
(izquierda / derecha) en la placa base
9
.
Las marcas impresas corresponden a los gra-
dos de ajuste en ángulo de corte. La carcasa
posee un perno de retención
21
, (véase fig. B)
que debe engatillarse en cada grado.
Apriete los tornillos de sujeción
11
con la
llave macho hexagonal
20
.
Ajustar el número de carreras
Ajuste el número deseado de carreras con
la rueda de ajuste (preselección de revolucio-
nes)
4
.
Averigüe siempre el mejor ajuste posible antes
de hacer un intento práctico.
Ajustar la carrera pendular
Puede ajustar el movimiento de carrera pendular
de la hoja de la sierra
12
con el interruptor de
control
14
. Sin movimiento de carrera pendular
12


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-pphss-730-se---kh-3021

Reset search

  • Hoe kom ik aan de 2 koolborstel houdertjes waar de koolborstels in zitten. Van beide houdertjes zijn de pennen waar de drukveer aan hoort te zitten afgebroken. Ook de beide drukveertjes voor de koolborstels zijn weg. Submitted on 16-11-2021 at 16:00

    Reply Report abuse
  • Is it possible to bye the speedcontrol as a part? It didn't start. Can rotate some when I give the fanwheel o puch.
    OR, howe to disconect the whole speedcontrol. Howe to conect the wires? Submitted on 9-6-2021 at 10:07

    Reply Report abuse
  • parkside pphss 730 se kh 3021 I didn't start the switch is ok Submitted on 18-6-2020 at 15:41

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PPHSS 730 SE - KH 3021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PPHSS 730 SE - KH 3021 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PPHSS 730 SE - KH 3021

Parkside PPHSS 730 SE - KH 3021 User Manual - German, Dutch, French, Italian - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info