576627

Parkside POF 1200 A1 - IAN 100129 Manual

11
Zoom out
Zoom in
Previous page
1/55
Next page
11 GB
Operation
5. Loosen the clamping lever
16
by turning it clock-
wise and pushing the device down until the route
bit touches the surface of the work-piece.
6. Lock the clamping lever in place
16
by turning
it anti-clockwise.
7. Push the depth stop
12
down until it reaches
the lowest position of the step stop
9
. Move
the index indicator
13
to the position “0“ on
the dial milling depth adjustment
14
.
8. Adjust the depth stop
12
to the desired depth,
tighten the lock screw
11
. Afterwards the index
indicator
13
should no longer be adjustable.
9. Loosen the clamping lever
16
and and lead the
device back up.
Readjust the milling depth
The milling depth can be adjusted with the con-
trol dial
15
.
Loosen the clamping lever
16
by turning it
clockwise and pushing the device down until
the depth stop
12
touches the step stop
9
.
Lock the clamping lever in place
16
by turning
it anti-clockwise.
Set the milling depth with the control dial
15
.
Loosen the clamping lever
16
by turning it clock-
wise and lead the device back up. Check the
milling depth through a further practical test.
Set the milling depth
with the step stop
You can use the step stop
9
with deeper depths in
several steps with less takeoff.
Set the desired milling depth with the lowest
step of the step stop
9
(as described above).
Then set it at higher level for the first attempt.
Milling direction
The milling process must always go against the
rotationary direction on the router bit
17
(Counter
rotation).
ATTENTION: When milling in the direction of the rout-
er bit (counter rotation) the device fly out of your hand.
Milling process
Set the milling depth as previously described.
Place the device on the desired work-piece and
switch it on.
Loosen the clamping lever
16
by turning it clock-
wise and pushing the device down until it touches
the surface of the depth stop
12
on the step
stop
9
.
Lock the device into place by turning the clamp
lever
16
anti-clockwise.
Mill with even speed and even pressure (see fig. I).
Set the copy casing
Set the copy casing
26
from below on the slid-
ing bar
8
.
Secure the copy casing
26
with the two screws
22
of the extractor adapter on the base plate
7
.
Ensure that the copy casing
26
is set the right
way round - the thrust ring
25
must be pointing
down (see fig. D).
Start-up / Operation
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside POF 1200 A1 - IAN 100129 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside POF 1200 A1 - IAN 100129 in the language / languages: English, German, Dutch, Swedish, Finnish as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info