779278

Parkside PMTS 210 A1 - IAN 367465 Manual

17
Zoom out
Zoom in
Previous page
1/152
Next page
11GB/IE
1. Allow the product to cool.
2. Press the overload switch (10).
3. Switch on the machine as described in 10.1.1.
10.2 Setting the cutting depth (fig. 1)
The saw blade (5) can be adjusted to the required cutting
depth by turning the hand wheel (8).
• Counterclockwise: Greater cutting depth
• Clockwise: Smaller cutting depth
Check the setting with a test cut.
10.3 Setting the angle (fig. 18)
Angled cuts of 0°-45° to the left of the parallel stop (7) can be
carried out with the circular table saw.
m Before making every cut, check that no collision can occur
between the stop rail (17), transverse stop (2) and the saw
blade (5).
1. Loosen the locking screw (9).
2. Set the desired angle on the scale by turning the hand
wheel (8a).
3. Lock the locking screw (9) at the desired angle setting.
10.4 Using the stop rail (17) on the parallel stop
(7) or transverse stop (2) (fig. 2, 13-14) (see
9.6 and 9.7)
10.4.1 Stop heights (fig. 13-14)
The stop rail (7) has two guide surfaces at different heights.
• Depending on the thickness of the materials to be cut, the
stop rail (17) must be used as follows:
-for thick material with a workpiece thickness of more than
25 mm, see fig. 13
-for thin material with a workpiece thickness of less than 25
mm, see fig. 14
10.4.2 Shifting the stop rail (fig. 13-14)
1. To move the stop rail (17) to the lower guide surface, loos-
en the two screws (16a). Then loosen the stop rail (17)
from the holder (16).
2. Pull out the stop rail (17) along the groove.
3. Turn the stop rail (17) and slide the sliding block along the
second groove (39).
4. Shifting to the higher guide surface must be carried out in
the same way.
10.4.3 Cutting width (fig. 13-14)
• The parallel stop (7) must be used when cutting sections of
wood lengthways.
• The parallel stop (7) can be mounted on both sides of the
saw table (1).
• With the help of the scales (38) on the saw table (1), the
parallel stop (7) can be set to the required dimension with
the stop rail (17).
• Tighten the two locking screws (15) to fasten the parallel
stop (7) in place.
• Perform a test cut to measure the width before cutting the
real workpiece. In this way you avoid inaccuracies with the
scale or the setting.
10.4.4 Setting the stop length (fig. 13-14, 19)
In order to avoid the material to be cut becoming jammed, the
stop rail (17) can slide in a longitudinal direction.
Rule of thumb: The rear edge of the stop should intersect an
imaginary line that starts roughly at the centre of the saw blade
and runs to the rear at 45°.
1. Set the required cutting width.
2. Loosen the screws (16a) and push the stop rail (17) for-
ward until the imaginary 45° line is touched.
3. Tighten the screws (16a) again.
10.5 Using the transverse stop (fig. 15)
When trimming, the transverse stop (2) must be extended from
the parallel stop (7) with the stop rail (17) (fig. 15).
10.5.1 Extending the transverse stop
1. Remove the stop rail (17) from the parallel stop (7). To do
so, loosen the screws (16a) and release the stop rail (17)
from the holder (16).
2. Slide the sliding block along the groove in the stop rail
(17).
3. Fasten the stop rail (17) with the help of the knurled screws
(18) on the transverse stop (2).
ATTENTION:
Do not slide the stop rail too far in the direction of the saw
blade. The distance between the stop rail (17) and the saw
blade (5) needs to be approx. 2 cm.
11. Operation
Working instructions
• After every new setting, we recommend performing a test
cut, in order to check the dimensional settings.
• After switching on the saw, wait until the saw blade has
reached its max. speed before making the cut.
• Be careful when cutting in.
• Only operate the device with an extraction system.
• Check and clean the extraction channels at regular intervals.
11.1 Performing longitudinal cuts (fig. 20)
Here, a workpiece is cut in its longitudinal direction. Hold the
edge of the workpiece against the parallel stop (7), whilst the
flat side lies on the saw table (1).
Ensure that the saw blade guard (4) always lowers onto the
workpiece. The working position for the longitudinal cut must
never be in line with the cutting process.
1. Adjust the parallel stop (7) according to the workpiece
height and the desired width (see 10.4).
2. Switch the saw on.
3. Place your hands flat on the workpiece with your fingers
closed and slide the workpiece along the parallel stop (7)
into the saw blade (5).
4. Lateral guidance with the left or right hand (depending on
the position of the parallel stop) only up to the front edge
of the saw blade guard (4).
5. Always push the workpiece through to the end of the riving
knife (3).
6. The cutting waste remains on the saw table (1) until the
saw blade (5) has completely stopped.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PMTS 210 A1 - IAN 367465 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PMTS 210 A1 - IAN 367465 in the language / languages: English, German, Dutch, Danish, French, Polish, Spanish as an attachment in your email.

The manual is 3.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info