722834
38
Zoom out
Zoom in
Previous page
1/242
Next page
38
GB IE
Clean the collection bag (
A
15) using
a brush and, if needed, compressed
air.
General maintenance
Prior to every use, check the appliance
for obvious defects such as loose, worn
or damaged parts.
Check covers and safety devices for
damages and correct installation. Re-
place as necessary.
Removal of clogging
and blockage
Leaf material and fresh plant parts may
clog / block the device.
Cleaning the impeller wheel:
Remove the batteries from the de-
vice! Risk of injury!
1. Open the protective cover (
7) or
remove the suction pipe (
16). See
section “Assembling/dismantling the
three-piece suction pipe” and/or “As-
sembling/dismantling the three-piece
blowpipe”.
2. Carefully remove residues or clogging
materials from the impeller wheel.
3. Check to make sure the impeller wheel
is easier to turn and is in undamaged
condition. Have our Service Centre re-
place a defective impeller wheel.
4. Close the protective cover (
7) or
screw the suction pipe (
16) back
into place.
See section “Assembling/dismantling
the three-piece suction pipe” and/
or “Assembling/dismantling the three-
piece blowpipe.
If the protective cover ( 7) and/
or the suction pipe (
16) is not
correctly screwed into place, it is
not possible to operate the device.
Storage
For storage purposes you can remove
the blow tube (
9) and/or the suction
tube (
16) and the catcher ( 15)
from the motor housing (
1) (see the
corresponding installation instructions
in the „Start-up” section).
Store the device in a dry place well
out of reach of children.
Disposal and protection
of the environment
Remove the battery from the device and re-
cycle the device, battery, accessories and
packaging in an environmentally-friendly
manner.
Machines do not belong with
domestic waste.
Do not throw batteries into dome-
sticwaste,re(riskofexplosion)
or water. Damaged batteries can
harm the environment and your
health if poisonous fumes or liquids
escape.
Hand over the device at an utilization
location. The plastic and metal parts
employed can be separated out and
thus recycled use can be implemented.
Ask our Service-Center for details.
Defective units returned to us will be
disposed of for free.
Dispose of batteries in a discharged
state. We recommend covering the con-
tacts with an adhesive strip to protect
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PLSA 40-Li A1 - IAN 315641 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PLSA 40-Li A1 - IAN 315641 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 3,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info