722834
30
Zoom out
Zoom in
Previous page
1/242
Next page
30
GB IE
Prolonged use of the device
can lead to blood circulation
disorders in the hands caused
by vibration. You can however
extend your machine use time by
wearing appropriate gloves or
by taking regular breaks.
Avoid operating the machine in
poor weather conditions, espe-
cially when there is a lightning
hazard. Only work in daylight
orwherethereisgoodarticial
illumination.
Do not vacuum burning, glowing
or smoking materials (e.g. ciga-
rettes, embers etc.), vapours or
highlyammable,toxicorexplo-
sive substances.
Stop the machine and remove
the batteries from the device. En-
sure that all moving parts are at
a full standstill:
- when you are not using the
device or when you are trans-
porting or leaving it unatten-
ded;
- before removing any obstruc-
tion or blocked channels,
- before checking, cleaning or
carrying out other work on
the machine.
- after contact with foreign bo-
dies or if abnormal vibration
occurs.
Do not use the device in a
closed or poorly ventilated area.
• Donotusethedevicenearam-
mable liquids or gases. There is
ariskofreorexplosionifthis
advice is not heeded.
In the case of an accident or
malfunction during operation,
the device must be switched off
immediately and the batteries
removed. Read the “Trouble-
shooting” section to correct any
malfunctions or contact our Ser-
vice Centre.
Walk at a steady pace, do not
run.
Ensure that the in-feed is empty
prior to starting the machine.
Keep your face and body away
from the in-feed aperture.
Do not allow hands or other
body parts or clothing to enter
the in-feed or discharge chute,
or to be in the vicinity of moving
parts.
Ensure you are standing securely
and do not lose your balance.
Avoid an abnormal work pos-
ture. When material is being
taken in by the machine, never
stand on a higher level than the
base of the machine.
Do not stand within the ejection
zone while operating the machine.
Take extreme care when feeding
material into the machine to en-
sure no metallic objects, stones,
bottles, canisters or other foreign
objects are taken in.
Do not allow processed material
to accumulate in the ejection
zone since this can prevent
proper ejection and cause the
material to be brought back
into the machine via the in-feed
aperture.
If the machine becomes
clogged, turn off the power sour-
ce and disconnect the machine
from the mains supply or remove
the batteries before freeing any
refuse.
Never operate the machine with
defective protective equipment
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PLSA 40-Li A1 - IAN 315641 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PLSA 40-Li A1 - IAN 315641 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 3,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info