733458
17
Zoom out
Zoom in
Previous page
1/50
Next page
16
GB IE NI
on and off ) to continue shredding
material.
7. If jam is not fixed, repeat above
steps. If still fail to fix, open the
blade cover (23) to clean
the jammed material,
a. Unplug the power supply
b. Loosen the four blade cover
screws (22) by enclosed Allen key
c. Pull to remove the blade cover
(23)
d. Clean the jammed material
from the cylinder blade (24) and
pressure plate (25).
e. Put the blade cover (23) back
and tighten the four screws (22)
8. Connect the power supply and
switch the shredder ON and OFF
(see " switching the shredder off
and on") to check.
Overload protection switch (12) not
motivated
1. Switch the shredder OFF
(see"switching the shredder on
and off ) .
2. Press the function switch (9)
upwards to allow the blade
rotate anti-clockwise to return the
material.
3. Press and hold the "ON" switch
(10) to start the machine to return
the jammed material.
4. Switch the shredder OFF and ON
(see" switching the shredder on
and off ) to check if the jam is
fixed.
5. If jam is fixed, switch the shredder
ON (see" switching the shredder
on and off ) to continue shredding
the material.
6. If jam is not fixed, repeat above
steps. If still fail to fix, open the
blade cover (23) to clean
the jammed material:
a. Unplug the power supply
b. Loosen the four blade cover
screws (22) by enclosed Allen
wrench.
c. Pull to remove the blade cover
(23)
d. Clean the jammed material
from the cylinder blade (24) and
pressure plate (25).
e. Put the blade cover (23) back
and tighten the four screws (22).
Connect the power supply and
switch the shredder OFF and ON
(see " switching the shredder on
and off") to check.
Adjusting the pressure plate
The pressure plate factory setting is correct
and only has to be adjusted when worn.
You will recognise that the cutting system has
become worn when the shredded material
is only compressed, and comes out in long
chains.
The running-in process may require that you
initially readjust the pressure plate (25) in
short intervals,
1. Check the funnel feeder (8) is
empty and clean.
2. Connect the power supply and
switch ON the machine to shred
the material(see" switching the
A
E
E
G
G
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PLH 2800 B2 - IAN 315130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PLH 2800 B2 - IAN 315130 in the language / languages: English, German as an attachment in your email.

The manual is 2,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PLH 2800 B2 - IAN 315130

Parkside PLH 2800 B2 - IAN 315130 User Manual - German, Dutch, French, Polish - 125 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info