Manual Parkside PKS 1500 B3 - IAN 346110 (page 12 of 100) (English, German, Dutch, Danish, French)

779274

Zoom out

Zoom in

1/100

7GB/IE/NI

15. Make sure that ﬁxed reducer rings are parallel to each other.

16. Handle insertion tool with caution. They are ideally

stored in the originally package or special containers.

Wear protective gloves in order to improve grip and to

further reduce the risk of injury.

17. Prior to the use of insertion tools, make sure that all pro-

tective devices are properly fastened.

18. Prior to use, make sure that the insertion tool meets the

technical requirements of this electric tool and is properly

fastened.

19. Only use the supplied saw blade for cutting wood, never

for the processing of metals.

20. Only use saw blade diameters in accordance with the

markings on the saw.

21. Use additional workpiece supports, if required for work-

piece stability.

22. Workpiece support extensions must always be secured

and used during work.

23. Replace table inserts when worn!

24. Avoid overheating of the saw teeth.

25. When sawing plastic, avoid melting of the plastic. Use

the appropriate saw blades for this purpose. Replace

damaged or worn saw blades immediately. When the

saw blade overheats, stop the machine. Allow the saw

blade to cool down before using the power tool again.

Attention: Laser radiation

Do not stare into the beam

Class 2 laser

Protect yourself and you environment from acci-

dents using suitable precautionary measures!

• Do not look directly into the laser beam with unprotected

eyes.

• Never look into the path of the beam.

• Never point the laser beam towards reﬂecting surfaces and

persons or animals. Even a laser beam with a low output can

cause damage to the eyes.

• Caution - methods other than those speciﬁed here can result

in dangerous radiation exposure.

• Never open the laser module. Unexpected exposure to the

beam can occur.

• If you do not use the device for a long time, the batteries

should be removed.

• The laser may not be replaced with a diﬀerent type of laser.

• Repairs of the laser may only be carried out by the laser

manufacturer or an authorised representative.

Safety instructions for handling batteries

1. Always make sure that the batteries are inserted with the

correct polarity (+ and –), as indicated on the battery.

2. Do not short-circuit batteries.

3. Do not charge non-rechargeable batteries.

4. Do not overcharge batteries!

5. Do not mix old and new batteries or batteries of diﬀerent

types or manufacturers! Replace an entire set of batteries

at the same time.

6. Immediately remove used batteries from the device and

dispose of them properly! Do not dispose batteries with

household waste. Defective or used batteries must be re-

cycled according to Directive 2006/66 / EC. Give back

batteries and / or the device has been oﬀered to the col-

lective facilities. About disposal facilities you can inform

by your municipal or city government.

7. Do not allow batteries to heat up!

8. Do not weld or solder directly on batteries!

9. Do not dismantle batteries!

10. Do not allow batteries to deform!

11. Do not throw batteries into ﬁre!

12. Keep batteries out of the reach of children.

13. Do not allow children to replace batteries without super-

vision!

14. Do not keep batteries near ﬁre, ovens or other sources of

heat. Do not use batteries in direct sunlight or store them

in vehicles in hot weather.

15. Keep unused batteries in the original packaging and

keep them away from metal objects. Do not mix un-

packed batteries or toss them together! This can lead to

a short-circuit of the battery and thus damage, burns or

even the risk of ﬁre.

16. Remove batteries from the equipment when it will not be used

for an extended period of time, unless it is for emergencies!

17. NEVER handle batteries that have leaked without appro-

priate protection. If the leaked ﬂuid comes into contact with

your skin, the skin in this area should be rinsed oﬀ under

running water immediately. Always prevent the ﬂuid from

coming into contact with the eyes and mouth. In the event

of contact, please seek immediate medical attention.

18. Clean the battery contacts and corresponding contacts in

the device prior to inserting the batteries.

Residual risks

The machine has been built according to the state

of the art and the recognised technical safety re-

quirements. However, individual residual risks can

arise during operation.

• Health hazard due to electrical power, with the use of im-

proper electrical connection cables.

• Furthermore, despite all precautions having been met, some

non-obvious residual risks may still remain.

• Residual risks can be minimised if the “Safety information“

and the “Proper use” are observed along with the whole of

the operating instructions.

• Do not load the machine unnecessarily: excessive pressure

when sawing will quickly damage the saw blade, which re-

sults in reduced output of the machine in the processing and

in cut precision.

• When cutting plastic material, please always use clamps:

the parts which should be cut must always be ﬁxed between

the clamps.

• Avoid accidental starting of the machine: the operating but-

ton may not be pressed when inserting the plug in an outlet.

• Use the tool that is recommended in this manual. In doing so,

your machine provides optimal performance.

• Hands may never enter the processing zone when the ma-

chine is in operation.

• Release the handle button and switch oﬀ the machine prior

to any operations.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKS 1500 B3 - IAN 346110 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 3.09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PKS 1500 B3 - IAN 346110 Manual

Product: