Manual Parkside PKS 1500 A1 - IAN 93463 (page 12 of 52) (English, German, Dutch, French)

706390

Zoom out

Zoom in

1/52

7GB/IE

m Assembly

WARNING! For you own safety, only insert the mains

plug in an outlet when all assembly steps have been

completed and you have read and understood the

safety and operating instructions.

Lift the saw out of the packaging and place it on your

work bench. (Positioning of the saw on the work bench

- see the next page under „POSITIONING / WORK STA-

TION“)

Installation of the dust bag

• Squeeze together the metal ring on the dust bag (12)

and attach it to the outlet opening in the motor area.

Assembling the work piece clamping device (g. 1.1)

• Loosen the locking screw (17) and attach the work

piece clamping device (10) to the left or right of the

xed saw bench.

• Afterwards, retighten the locking screws (17).

Assembling the work piece supports (g. 1.1 – 1.2)

• Loosen the cross-head screw (14) and guide the work

piece support through the specied hole on the side of

the xed saw bench.

• Make sure that the work piece support (15) is also

guided through the two plates (19) on the underneath.

• Afterwards, retighten the cross-head screw (14).

• Repeat this process on the other side.

Assembling the support stand (g. 1.1 – 1.2)

• Loosen the cross-head screws (18) on the underneath

of the saw and guide the support stand (16) through

the specied holes on the back of the saw.

• Afterwards, retighten the cross-head screws (18).

m Area of application

Intended application possibilities

The machine cuts:

• Wood and materials similar to wood

• Plastic

Unintended application possibilities

The machine is not suitable for:

• Ferritic materials, steel and cast iron, as well as other

material types which are not listed, particularly food.

• Mitre saw without guard.

• Materials larger than the specied cutting data:

90°/90°/ 120 x 60 mm

90°/45° 80 x 60 mm

45°/90° 120 x 35 mm

45°/45° 80 x 35 mm

Settings

CROSS-CUTTING

ATTENTION: Before carrying out the following adjust-

ments, please check whether the motor of the machine

is switched off.

Pivoting the table plate (Fig. 2)

The mitre saw can be pivoted left and right with the rota-

ry table. Exact angle adjustment is possible on the basis

of the scale. The angle can be precisely and quickly ad-

justed from 0° to 45° with locking positions at 15°, 22.5°

and 30°.

To pivot the rotary table, loosen the set screw (21) and

rotate the unit using the handle (20) until the desired

angle is reached. Then secure it with the set screw (21).

Tilt of the saw unit (Fig. 3)

The saw unit can be tilted at an angle of up to 45°.

Loosen the handle (23) on the rear side of the machine

and tilt the unit to the desired angle position according to

the scale. The angle can be set on the basis of the scale

(24) using the pointer (25). Then the handle must be re-

tightened.

Working instructions

After you have carried out all the tasks described above,

you can begin working.

ATTENTION: Always keep your hands away from the

cutting zone and never attempt to reach in while cutting.

FIXING A WORKPIECE

Clamp the work piece on the work table with the workpi-

ece clamp (10 - Fig 1) in order to x it in place.

Cross-cutting (Fig. 4)

• Loosen the locking knob (26).

• Lift the saw unit by the handle (2) until it locks in place

in the top position

• Press the workpiece evenly on the stop strips (27);

make sure that you hand remains outside the cutting

area of the saw blade.

• With your right hand on the handle (2), press the lo-

cking lever (3) so that the unit can also be pivoted

downward.

• The motor starts when the start button (1) is pressed.

• Slowly bring the saw blade down to the workpiece and

cut through it with moderate pressure.

• Pivot the unit back to the upper starting position into

it locks in place.

• Release the handle (2) so that the motor switches off.

Saw blade replacement (Fig. 5)

• Pull out the mains plug.

• Place the saw unit in „cross-cutting“ position

• Unlock the moving saw blade guard (6) by pressing

the lock (3 - Fig. 1); in the process, raise the saw bla-

de guard so that the saw blade is free.

• Actuate the spindle lock (22 - Fig. 3).

• Loosen the saw blade fastening screw (28) - (Atten-

tion: left-handed thread).

• Remove the screw (28) and saw blade ange (29).

• Carefully remove the saw blade (risk of injury from the

saw blade teeth).

• Place a new saw blade on the inner saw blade an-

ge. In the process, observe the rotational direction of

the saw blade.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKS 1500 A1 - IAN 93463 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PKS 1500 A1 - IAN 93463 Manual

Product: