Manual Parkside PKO 270 A1 - IAN 96894 (page 11 of 44) (English, German, Dutch, French)

595284

Zoom out

Zoom in

1/44

6 GB/IE

• Kinks where the connection cable has been improp-

erly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage

regularly. Make sure that the connection cable does

not hang on the power network during the inspection.

Electrical connection cables must comply with the ap-

plicable VDE and DIN provisions. Only use connection

cables with the marking „H05VV-F“.

The printing of the type designation on the connection

cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must have a

cross-section of 1.5 mm

Connections and repairs of electrical equipment

may only be carried out by an electrician.

Please provide the following information in the event of

any enquiries:

• Type of current for the motor

• Machine data - type plate

10. Cleaning, maintenance, and storage

n Important!

Pull out the power plug before doing any cleaning

and maintenance work on the equipment. Risk of

injury from electric shock!

n Important!

Wait until the equipment has cooled down complete-

ly! Risk of burns!

n Important!

Always depressurize the equipment before carrying out

any cleaning and maintenance work! Risk of injury!

10.1 Cleaning

• Keep the equipment free of dirt and dust as far as pos-

sible. Wipe the equipment with a clean cloth or blow it

down with compressed air at low pressure.

• We recommend that you clean the equipment imme-

diately after you use it.

• Clean the equipment regularly with a damp cloth and

some soft soap. Do not use cleaningagents or sol-

vents; these may be aggressive to the plastic parts in

the equipment. Ensure that no water can get into the

interior of the equipment.

• You must disconnect the hose and any spraying tools

from the compressor before cleaning. Do not clean the

compressor with water, solvents or the like.

10.2 Maintenance work on the pressure vessel (Fig. 1)

n Important! To ensure a long service life of the

pressure vessel (7), drain off the condensed water

by opening the drain valve (9) each time after using.

Release the vessel pressure  rst (see 10.7.1). Open

the drain screw by turning counter-clockwise (looking at

the screw from the bottom of the compressor) so that all

the condensed water can run out of the pressure vessel.

Then close the drain screw again (turn it clockwise).

Check the pressure vessel for signs of rust and damage

each time before using. Do not use the compressor with

a damaged or rusty pressure vessel. If you discover

any damage, then please contact the customer service

workshop.

n Important!

The condensed water from the pressure vessel will

contain residual oil. Dispose of the condensed water

in an environmentally compatible manner at a suita-

ble collection point.

10.3 Safety valve (Figure 3)

The safety valve (19) has been set for the highest per-

mitted pressure of the pressure vessel. It is prohibited

to adjust the safety valve or remove its seal. Actuate

the safety valve from time to time to ensure that it works

when required. Pull the ring with suf cient force until

you can hear the compressed air being released. Then

release the ring again.

10.4 Checking the oil level at regular intervals (Fi-

gure 11)

Place the compressor on a level and straight surface.

The oil level must be between the MAX and MIN marks

on the oil level window (Fig. 18).

Oil change: we recommend SAE 15W 40 or equivalent.

The original oil  lling must be changed after 100 hours

in operation; thereafter the oil must be drained and

replaced with new oil after every 500 hours in operation.

10.5 Changing the oil (Figure 1,10, 11)

Switch off the engine and pull the mains plug out of

the socket. After releasing any air pressure you can

unscrew the oil drain plug (12) from the compressor

pump (13).

To prevent the oil from running out in an uncontrolled

manner, hold a small metal chute under the opening

and collect the oil in a vessel. If the oil does not drain

out completely, we recommend tilting the compressor

slightly. When the oil has drained out, re t the oil drain

plug (12).

Dispose of the old oil at a drop-off point for old oil.

To  ll in the correct quantity of oil, make sure that the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKO 270 A1 - IAN 96894 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PKO 270 A1 - IAN 96894 Manual

Product: