763019

Parkside PK0 400 A1 - IAN 73783 Manual

55
Zoom out
Zoom in
Previous page
1/62
Next page
GB
- 55 -
9. Cleaning, maintenance,
storage, ordering spare
parts and transport
Important!
Pull out the power plug before doing any
cleaning and maintenance work on the
equipment. Risk of injury from electric
shock!
Important!
Wait until the equipment has cooled
down completely! Risk of burns!
Important!
Always depressurize the equipment be-
fore carrying out any cleaning and main-
tenance work (see 9.7.1)! Risk of injury!
9.1 Cleaning
• Keep the equipment free of dirt and dust as
far as possible. Wipe the equipment with a
clean cloth or blow it down with compressed
air at low pressure.
• We recommend that you clean the equipment
immediately after you use it.
• Clean the equipment regularly with a damp
cloth and some soft soap. Do not use cleaning
agents or solvents; these may be aggressive
to the plastic parts in the equipment. Ensure
that no water can get into the interior of the
equipment.
• You must disconnect the hose and any
spraying tools from the compressor before
cleaning. Do not clean the compressor with
water, solvents or the like.
9.2 Maintenance work on the pressure
vessel (Figure 1)
Important! To ensure a long service life of the
pressure vessel (7), drain off the condensed water
by opening the drain valve (9) each time after
using. Release the vessel pressure fi rst (see 9.7.1).
Open the drain screw by turning counter-clock-
wise (looking at the screw from the bottom of the
compressor) so that all the condensed water can
run out of the pressure vessel. Then close the drain
screw again (turn it clockwise). Check the pressure
vessel for signs of rust and damage each time
before using. Do not use the compressor with a
damaged or rusty pressure vessel. If you discover
any damage, then please contact the customer
service workshop.
Important!
The condensed water from the pressure
vessel will contain residual oil. Dispose
of the condensed water in an environ-
mentally compatible manner at a suitable
collection point.
9.3 Safety valve (Figure 3)
The safety valve (19) has been set for the highest
permitted pressure of the pressure vessel. It is
prohibited to adjust the safety valve or remove its
seal. Actuate the safety valve from time to time to
ensure that it works when required. Pull the ring
with suffi cient force until you can hear the com-
pressed air being released. Then release the ring
again.
9.4 Checking the oil level at regular inter-
vals (Figure 11)
Place the compressor on a level and straight sur-
face. The oil level must be between the MAX and
MIN marks on the oil level window (Fig. 18). Oil
change: we recommend SAE 15W 40 or equiva-
lent. The original oil fi lling must be changed after
100 hours in operation; thereafter the oil must be
drained and replaced with new oil after every
500 hours in operation.
9.5 Changing the oil (Figure 1,10, 11)
Switch off the motor and pull the mains plug out
of the socket. After releasing any air pressure (see
9.7.1) you can unscrew the oil drain screw (18)
from the compressor pump (13). To prevent the oil
from running out in an uncontrolled manner, hold
a small metal chute under the opening and collect
the oil in a container. If the oil does not drain out
completely, we recommend tilting the compressor
slightly. When the oil has drained out, refi t the oil
drain screw (18).
Anleitung_4010411_LB2.indb 55Anleitung_4010411_LB2.indb 55 12.03.12 09:5212.03.12 09:52
… 55 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PK0 400 A1 - IAN 73783 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PK0 400 A1 - IAN 73783 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info