733445
26
Zoom out
Zoom in
Previous page
1/106
Next page
22 
GB
IE
PHSHE 900 B2
Before use
CAUTION! RISK OF INJURY!
Before any work on the appliance, disconnect the plug.
Risk of electric shock!
Motor unit
Attaching the round handle
Place the round handle in the desired position on the boom .
Tighten the screw
.
Fastening/attaching the shoulder strap
Hook the shoulder strap into the carrying lug .
Adjust the length of the shoulder strap
to your size so that the carrying
lug
is at hip height when the strap is hooked in place.
Assembling the hedge trimmer
Push the front boom of the hedge trimmer onto the boom of the
motor unit.
The locking pin
must engage.
Secure the two booms
with the tommy screw ; to do this, fit
the nut
on the opposite side.
Mounting the pole pruner
Push the front boom of the pole pruner to the boom of the motor
unit.
The locking pin
must click into place.
Secure the two booms
with the tommy screw ; to do this, fit
the nut
on the opposite side.
Swivelling of the hedge trimmer
Trigger the lock/release .
Press the control lever
and swivel the hedge trimmer into the
desired position.
Allow the control lever
and the lock/release to click into the
recess in the base plate (hedge trimmer)
.
Swivelling of the pole pruner
Release the lock/release .
Press the control lever
and swivel the pole pruner into the desired
position.
Allow the control lever
and the lock/release to click into the
recess in the base plate (pole pruner)
.
Mounting the saw chain and blade
WARNING!
Wear protective gloves! There is a danger of injury from the sharp
cutting teeth!
NOTE
Pay close attention to the running direction of the saw chain
on
the blade and at the sprocket cover
.
The blade
and the saw chain are already assembled upon
delivery.
Depending on wear, the blade can be turned.
Undo the nut
using the assembly tool .
Remove the sprocket cover
.
You may have to loosen the saw chain
to remove the blade
and the saw chain
(see section "Tightening and checking the saw
chain"). Follow these instructions in reverse order.
Remove the blade
with the saw chain from the base plate
(pole pruner)
.
Reset the saw chain
starting at the top of the blade .
Lay the guide rail
over the blade guide , while inserting the chain
roll pin
in the blade hole . At the same time, lay the saw chain
over the chain sprocket
.
Replace the sprocket cover
and tighten the nut gently.
Now you can tighten the saw chain
(see section “Tightening and
checking the saw chain”).
Tightening and checking the saw chain
NOTE
The tension of the saw chain
is important for your safety and the
function of the appliance. A correctly pre-stressed saw chain
increases the service life of your appliance.
WARNING!
Wear protective gloves! There is a danger of injury from the sharp
cutting teeth!
Loosen the nut
a little using the assembly tool .
Using the assembly tool
, turn the chain adjuster screw in a
clockwise direction to increase the tension.
Using the assembly tool
, turn the chain adjuster screw
in an
anticlockwise direction to decrease the tension.
The saw chain
must lie against the underside of the blade. Check
whether the saw chain
can be drawn over the blade
by hand.
Tighten the nut
using the assembly tool .
NOTE
When pulling on the saw chain
with a force of 9 N (approx. 1 kg),
the gap between the saw chain
and blade should not be more
than 2 mm.
A new saw chain stretches and must be tightened more frequently.
Check the chain tension before each use of the appliance.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PHSHE 900 B2 - IAN 313266 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PHSHE 900 B2 - IAN 313266 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info