558823
13
Zoom out
Zoom in
Previous page
1/29
Next page
13 GB/IE/CY
Preparing for use
Switching off:
Release the ON / OFF switch
3
.
Setting the cutting angle
You can set the cutting angle accurately with the
help of the cutting angle scale
12 b
.
Release the wing screws / locking bolts of the
cutting angle preselector
9
on both sides, set
the desired angle on the cutting angle scale
12 b
and retighten the wing screws / locking bolts.
Setting the cutting depth
Note: If possible we recommend that the cutting
depth is set approximately 3 mm greater than the
material thickness. This should help to ensure you
achieve a clean cut.
Release the wing screw on the cutting depth
setting clamp
5
, set the required cutting depth
on the scale
19
and retighten the wing screw.
Setting the guide fence
Release the wing screw
13
of the base plate
8
and insert the guide fence
15
into the slot
14
.
Retighten the wing screw
13
.
Switching the laser on and off
Switching on:
Move the laser ON / OFF switch
11
to setting “I”.
Switching off:
Move the laser ON / OFF switch
11
to setting “0”.
Note: If the batteries are exhausted replace them
with two 1.5 V alkaline batteries LR44 (e.g. GPA 76).
Working with the circular saw
1. Switch on the device as described in the section
about “Switching on and off” and then place it
first with the front edge of the base plate
8
against the material.
2. Align the device using the guide fence
15
or
with reference to marked-out line or by using
the laser.
3. Hold the machine with both hands by the
handles (see Fig. A) and saw the material
with moderate pressure.
Setting the speed
Turn the wheel
1
to the desired speed setting
(arrow marking )
(1 = lowest speed / 6 = highest speed):
Use the general settings suggested in the following
table (information offered without liability) or adjust
the speed setting on the setting wheel
1
to the
material being cut.
Material Speed
setting
Hard- and softwood (solid wood)
cut longitudinally and transversely
6
Plywood, hard fibre board 6
Chipboard 6
Blockboard, laminated wood 6
Coated and veneered board 6
PVC board 3-5
Acrylic glass panels, Plexiglas 2-4
Aluminium board 4-6
Aluminium profiles 4-6
Plasterboard 1-2
Mineral wool board 1-2
Cement-bound chipboard 1-2
The circumferential speeds at minimum and maximum
rotational speeds are approx.:
Setting Rpm Metres/ sec
1 2,200 21.8
6 5,200 51.7
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PHKS 66 - KH 3026 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PHKS 66 - KH 3026 in the language / languages: English as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PHKS 66 - KH 3026

Parkside PHKS 66 - KH 3026 User Manual - German, Dutch, French - 41 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info