Manual Parkside PHKS 66 - KH 3026 (page 10 of 29) (English)

558823

Zoom out

Zoom in

1/29

10 GB/IE/CY

c) Set the cutting depth to match the thick-

ness of the workpiece. Less than a full tooth

height should be visible below the workpiece.

d) Never hold the workpiece in your hand

or steady it with your leg whilst saw

ing.

Keep the workpiece steady on a stable

supporting surface. It is important to see that

the workpiece is ﬁrmly held in place to minimise

any danger of it making contact with your body,

jamming of the saw blade or loss of control.

e) Hold the device by the insulated handle

surfaces when you are undertaking

work where there is the danger of the

cutting tool striking hidden electricity

cables or the device‘s mains lead. Con-

tact with a live wire means that the metal parts

of the device may also become live and this

can result in an electric shock.

f) When cutting longitudinally always use

a guide fence or a straight edge guide.

This will improve the accuracy of your cut and

reduce the risk of the blade jamming.

g) Always use a saw blade of the correct

size and with the appropriate central

fixing hole bore. Saw blades that do not

correspond with the attachment components

on the saw will not run true and could lead to

loss of control.

h) Never use a damaged or incorrect

saw blade washer or screw. The saw

blade washer and screw have been specially

designed to give your saw optimum performance

and safety in use.

To avoid the device kicking back:

Kickback occurs as a result of incorrect use or mis-

use of the saw. It can be prevented by taking the

appropriate precautions as described below.

a) Hold the saw with both hands and

bring your arms into a position in

which you will be able to withstand

any kickback forces. Always stand to

the side of the saw blade and never

bring your body in line with the saw

blade. When kickback occurs, the circular

saw may jump backwards but the operator

can control the kickback forces by adopting

suitable precautions.

b) If the saw blade jams or sawing stops

for another reason, release the ON /

OFF switch and hold the saw in the

workpiece without moving it until the

saw blade comes to a complete stand

still. Never try to remove the saw from

the tool or to pull it backwards as long

as the saw blade is still moving other-

wise this could cause a recoil action.

Find the reason for the saw blade jamming

and take the appropriate action to rectify it.

c) If you wish to restart a saw that has

been inserted into the workpiece, cen-

tre the saw blade in the saw gap and

check that the saw teeth do not catch

on the workpiece. If the saw blade jams, it

may move itself out of the workpiece or cause

a kickback when the saw is restarted.

d) Support boards whilst cutting to reduce

the risk of kickback caused by a

jammed saw blade. Large boards may

bend under their own weight. Boards must be

supported on both sides as well as near the

saw gap and at the edges.

e) Do not use blunt or damaged saw

blades. Saw blades with blunt or misaligned

teeth are in eﬀect too wide for the designed saw

gap and this gives rise to increased friction,

jamming and kickback.

f) Make sure that the cutting depth and

angle setting fastenings are tightened

before sawing starts. If these settings

move during sawing, this can lead to the saw

blade jamming and kickback.

g) Be particularly careful when carrying

out

a plunge cut in an obscured area, e.g.

in an existing wall. The plunging blade

could

jam in a hidden object and cause kickback.

Causes of kickback:

a) A kickback is a sudden reaction to a saw blade

becoming hooked, jammed or misaligned. This

causes an out of control circular saw to raise

itself and move out of the workpiece and towards

the operator.

b) If the sawblade becomes hooked or trapped in

a narrowing saw gap, it is suddenly prevented

General safety advice for electrical power tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PHKS 66 - KH 3026 in the language / languages: English as an attachment in your email.

The manual is 0,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PHKS 66 - KH 3026

Parkside PHKS 66 - KH 3026 User Manual - German, Dutch, French - 41 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PHKS 66 - KH 3026 Manual

Product: