595335
10
Zoom out
Zoom in
Previous page
1/66
Next page
10 GB/IE
Adjust the shoe
5
to suit the cutting depth.
To do this release the shoe adjustment lever
8
and place the shoe
5
in appropriate position.
Lock the shoe in this position by pulling the
shoe adjustment lever
8
tight.
Q
Setting the blade speed
With the oscillation speed setting wheel
1
you can
chose the desired stroke rate (- = lower stroke rate,
+ = higher stroke rate).
The stroke setting can also be changed during op-
eration.
Q
Preparing for use
Q
Switching on and off
When operating the device you can select between
intermittent or continuous operation mode.
To switch on intermittent operation mode:
Press the ON / OFF switch
3
.
To switch off intermittent operation mode:
Release the ON / OFF switch
3
.
To switch on continuous operation mode:
Press the ON / OFF switch
3
and fix it in the
pressed position with the lock button
2
.
To switch off continuous operation mode:
Press the ON / OFF switch
3
and release it
again.
Q
Guiding the sabre saw
safely and accurately
The shoe
5
pivots to adjust to the workpiece and
provides safe support to the device. It must always
lie against the workpiece when the device is in use.
Q
Advice about ways of
working when sawing
Before sawing, check the workpiece for foreign
bodies such as nails, screws etc. and remove
them.
Do not allow the ventilation slots to become
covered.
Switch the device on first and only then bring it
into contact with the workpiece.
If the saw blade jams, switch off the device im-
mediately.
Open the sawn gap in the workpiece slightly
using a suitable tool and extract the saw blade.
Always make sure the saw blade type and the
blade oscillation speed are suitable for the
workpiece material.
There are different saw blades available in var-
ious lengths designed to ensure optimum perfor-
mance of every sawing task with your sabre saw.
Saw the material using a steady forward rate
of progress.
Flush sawing:
Using flexible saw blades of adequate length you
can trim off projecting workpieces, such as pipes,
directly at the face of a wall.
Follow these steps:
1. Place the saw blade directly on the wall surface.
2. Bend the blade by applying sideways pressure
so that the shoe
5
comes up against the wall.
3. Switch on the device as described above and
trim the workpiece using constant pressure.
Plunge sawing:
CAUTION! DANGER OF KICKBACK!
Plunge sawing can be used only in soft materials
(such as wood etc.).
Follow these steps:
1. Place the sabre saw with the underside of the
shoe
5
against the workpiece.
Switch on the device.
2. Tilt the sabre saw forward and plunge the saw
blade into the workpiece.
Before use / Preparing for use Preparing for use / Maintenance and cleaning / Service centre / Warranty
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PFS 710 B1 - IAN 106629 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PFS 710 B1 - IAN 106629 in the language / languages: English, German, Dutch, Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info