679220
8
Zoom out
Zoom in
Previous page
1/38
Next page
PFS 400 A1
GB
IE
NI
CY
 5
5. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Additional safety instructions for
paint spray guns
Keep your work area clean, well lit and free
of paint and solvents, cloths and other inflam-
mable materials. Possible risk of spontaneous
combustion. Have a fully functioning fire extin-
guisher available at all times.
Ensure adequate ventilation in the spray zone
and sufficient fresh air in the entire room.
Evaporation of flammable solvents will cause an
explosive environment.
Do not spray or clean with materials whose
ignition point is lower than 21°C. Use ma-
terials based on water, non-volatile hydro-
carbons or similar materials. The evaporation
of volatile solvents will cause an explosive
environment.
Do not spray near ignition sources such as
static electric sparks, open flames, ignition
flames, hot items, motors, cigarettes or sparks
caused by plugging in/unplugging power
cables or by operating switches. These ignition
sources could ignite a fire in the environment.
Do not spray any material if you do not know
whether it is potentially dangerous. Unknown
materials can cause hazardous conditions.
Wear additional personal protective equip-
ment such as suitable gloves and a protective
mask/respirator when spraying or handling
chemicals. Wearing appropriate protective
equipment for the conditions reduces your expo-
sure to dangerous substances.
Be aware of the potential hazards of the
sprayed material. Take note of the markings
on the container and the manufacturer's infor-
mation on the sprayed material, including the
instructions to use personal protective equip-
ment. The manufacturer's instructions are to
be followed to reduce the risk of fire or injuries
caused by poisons, carcinogens, etc.
Do not use the spray gun to spray flammable
substances. Do not clean spray guns with flam-
mable solvents.
WARNING!
Be aware of any dangers inherent to the
spray material and pay attention to all pack-
aging labels and other information provided
by the producer of the substance.
Working procedures
Viscosity
The appliance can process spray materials up to a
maximum 70 DIN/s. (viscosity). You can deter-
mine the viscosity (thickness) of the substance with
the supplied measuring cup using a simplified
measuring procedure.
Fill the supplied measuring cup to the brim
with the spray material.
Remove the measuring cup from the spray
material and allow the liquid to run out.
Measure the time (in seconds) until the stream
of liquid stops. The resulting value is referred to
as DIN seconds (DIN-s).
If the value is too high, gradually thin the spray
material by adding small amounts of a suitable
thinning agent in and mixing the liquid.
Measure the DIN seconds again. Repeat the
process until you measure a viscosity of less
than 70 DIN/sec.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PFS 400 A1 - IAN 307721 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PFS 400 A1 - IAN 307721 in the language / languages: English as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PFS 400 A1 - IAN 307721

Parkside PFS 400 A1 - IAN 307721 User Manual - German, Dutch, French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info