576717

Parkside PFS 100 C3 - IAN 97735 Manual

30
Zoom out
Zoom in
Previous page
1/33
Next page
30 GB
Maintenance and cleaning / Service centre / Warranty / DisposalAdvice on use / Bringing into use / Maintenance and cleaning
* This device cannot be used to spray media contain-
ing discrete particles / solids. The abrasive effect
of these media shortens pump and valve life.
Q
Preparing the surface
to be sprayed
The surface to be sprayed must be clean, dry and
free of grease.
Roughen smooth surfaces and remove any
abraded dust.
Always cover the surrounding area around the
surface to be sprayed. The spray cloud may
contaminate the surrounding area.
Q
Bringing into use
Q
Selecting the nozzle
Nozzle Use
Nozzle, 0.6 mm
(R6)
8
all paints, varnishes
Nozzle, 0.8 mm
(R8)
8
thick-flowing sprayed media
Cleaning nozzle
11
a thinner, harder spray for
spot-cleaning of surfaces
Nozzle extension
13
for spraying into corners
which are difficult to reach
Q
Switching ON / OFF
Switching on:
To start the electrical power tool, press the
ON / OFF switch
3
and keep it pressed.
Switching off:
To switch off the electrical power tool, release
the ON / OFF switch
3
.
Q
Spraying process
1. You can vary the spray by adjusting the regulator
button
2
(see Fig. D). The spray is correctly
set when no drops are formed and the gun
produces a fine, consistent spray pattern.
2. Do not switch the device on or off while it is
over the surface to be sprayed. Instead, start
and stop the spraying process approximately
10 cm outside the surface to be sprayed.
NOTE: The distance between the nozzle and
the workpiece depends on the material being
sprayed (approx. 20 to 35 cm spraying dis-
tance, depending on the spray cone and the
desired amount of material to be applied).
Use the device in a horizontal orientation only
(as shown in Fig. D).
Carry out a trial in each case to determine the
most effective spraying distance.
Start with a longer distance.
3. Spray corners or small decorative details first
using short bursts of spray.
Then go on to the actual spraying process.
4. The spray process should follow the sequence
shown in Fig. E
– keep the spray gun moving parallel to the surface
– Do not incline the spray gun
– Move the spray gun at a constant speed
– Apply the sprayed medium as thinly as possible
– The layer(s) of sprayed medium need(s) to
be allowed to dry for some time before you
apply the next coat (Fig. F) at right angles to
the previous coat.
5. Do not allow the paint cup
7
to empty com-
pletely while spraying – drops may form!
Q
Maintenance and cleaning
General advice:
1.
Pull out the mains plug be-
fore you carry out any tasks on the spray gun.
Do the same when you take a break from spraying.
2. After each use, spray thinners (in the open
air only – danger of explosion!) or
water through the device.
3. To protect from rust after cleaning, you can
spray sewing machine oil through the device.
4.
DANGER TO LIFE
THROUGH ELECTRIC SHOCK! Never im-
merse the device in the cleaning medium.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PFS 100 C3 - IAN 97735 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PFS 100 C3 - IAN 97735 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PFS 100 C3 - IAN 97735

Parkside PFS 100 C3 - IAN 97735 User Manual - French - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info